HPCL Placement Papers for Electrical stream

Will you please share the HPCL Placement Papers for Electrical stream????????

As per your request here I am sharing the HPCL Placement Papers for Electrical stream

ELECTRONICS

Q. Power diode is generally made from
a) Silicon
b) Germanium
c) Both
d) None of these

Q. When the both junction of NPN diode is reverse biased, then the diode is in which mode
a) Active
b) Cutoff
c) Saturation
d) inverted

Q. Which transistor mode gives the inverted output
a) Common Emitter
b) Common Base
c) Common Collector
d) None of these

Q. Which coupling gives the higher gain in case of amplifier
a) Capacitor coupling
b) Impedance coupling
c) Transformercoupling

Q. Which distortion is least objectionable in audio amplification
a) Phase
b) Frequency
c) Harmonic
d) Intermediation

Q. A narrow band amplifier has a band pass nearly…………of central frequency
a) 33.3%
b) 10%
c) 50%

Q. Phase shift oscillator consists
a) RL
b) RC
c) RLC

Q. Multivibrater Produces
a) Sine wave
b) Square wave
c) Smooth wave
d) sawtooth

Q. Convert the 101101 Binary number into octal no
a) 65
b) 55
c) 51
d) 45

Ans: 55

Q. 10 in BCD
a) 10100
b) 1100
c) 010111
d) None of these

Ans: None of these

Q. Which PNP device has a terminal for synchronizing purpose
a) SCS
b) Triac
c) Diac
d) SUS

Q. Addition of indium in semiconductor crystal makes
a) PNP
b) NPN

Q. Free electron exists in which band
a) 1
b) 2
c) 3
d) Conduction band

Q. Ripple factor of half wave rectifier
a) 1.21
b) 0.48
c) 0.5

Q. Transistor that can be used in enhancement mode
a) NPN
b) UJT
c) JFET
d) MOSFET

Q. Following contributes to harmonic distortion in Amplifier
a) +Ve feedback
b) –Ve feedback
c) Defective active device

Q. High cutoff frequency
a) CB
b) CC
c) CE

Q. Which is used as data selector?
a) Encoder
b) Decoder
c) modulator
d) Demodulator

Q. Read write capable memory
a) RAM
b) ROM
c) Both
d) None of these

Q.the radix or base of hexadecimal number system is ———–
a) 8
b) 16
c) 5
d) none of these

Ans: 16

Q.the no of 1’s in the binary representation of the expression 162*9+162*7+16*5+3 are
a) 10
b) 23
c) 6
d) 4

Q. the no of latches in F/F are ——-
a) 1
b) 2
c) 3
d) 4

Q.how many flip-flops are required to construct Mod -12 counter
a) 5
b) 4
c) 12
d) none

Ans: 4

Q. which logic gate has the output is compliment of its input ———-
a) OR
b) AND
c) NOT
d) X-OR

Ans: NOT

Q.no.of 2-input multiplexers needed to construct a 210 input multiplexer…….
a) 12
b) 31
c) 20
d) 16

Q.By adding inverters to the inputs and output of a AND gate we can obtain ……………
a) OR
b) AND
c) NOT
d) X-OR

Ans: X-OR

Q.how many NAND gates are needed to realize OR gate ————–
a) 1
b) 2
c) 3
d) 4

Ans: 3

Q.which is the first integrated logic family —————
a) RTL
b) DTL
c) TTL
d) none of these

Q. Which logic gate has output high if and only if all inputs are low ———?
a) NOR
b) NAND
c) X-NOR
d) AND

Ans: NAND

Q.According to Boolean algebra 1+A+B+C =
a) A
b) A+B+C
c) 1
d) none of these

Ans: 1

Q. If a=0x6db7 and b=0x2ae9 then what is the value of a”b————–
a) binary number for 1001.1101?
b) decimal number for 19?
c) excess-3 code for 29?

Q.what is the value of A’+1 ?
a) A
b) A’
c) 1
d) none of these

Ans: 1

Q.2 in 4 bit number one bit indicates sign of the number then the locations are from
a) -8 to 8
b) -7 to 7
c) -16 to 16
d) None

Q.Avalanche photo diode is used when compared to PIN diode bcz
a)larger band width
b)high sensitivity
C)——-
d)——–

Q.some non zero DC voltage is to RC low pass circuit then the DC voltage in the output contains
a) Same as in input
b) Higher than input
c) Zero
d) Slightly increases

Q.if the output of the gate is always high then the gates applied to this logic are 0,0
a) NAND and EX-NOR
b) NAND and NOR
c) AND and X-NOR
d) OR and XOR

Ans:a

Q.Thermal Run away is not possible in FET bcz the flow of
a)minority careers
b)Transconductance
c)_____
d)none

Ans : minority careers

Q.which of the following is/are true about 1′s and 2′s compements:
i)In 1′s complement form. 0 has two representations
ii)in 1′s complement, the magnitude of lowest number is equal to the magnitude of highest number
iii)In 2′s complement, 0 has two representations

a) i only
b) i and ii
c) iii only
d) all of these

Q.In the hybrid parameter model of a transistor reverse transfer voltage ratio and forward transfer current ratio are respectively given by:
a) h11 and h21
b) h12 and h11
c) h21 and h11
d) None of these

Q.The largest negative no can be represented with 8 bits in 2′s compliment representation?
a)-256
b)-255
c)-127
d)-128

Ans: -128

Q. How many NAND gates required to implement AB+CD+EF
a) 1
b) 2
c) 3
d) 4

Ans: 4

Q. Transparent latch is seen in which type of flip flop
a) SR FF
b) D FF
c) JK FF
d) D FF

Ans: D FF

Q. Odd parity generator uses which logic?
a) Digital
b) Analog
c) Sequential
d) none

Q. Which type of ADC is fastest?
a) SARC
b) Counter type
c) Intigrated type
d) Flash

ANS: Flash/Parallel

Q. Which one of the following is fastest read/writable memory?
a) PROM
b) EEPROM
c) Flash
d) none

Ans: Flash

8. In array programming which one is used
a) SISD
b) PISD
c) MISD
d) None

Q.Which one of the following has high I/p impedance
a) CC
b) CB
c) CE
d) None

Q. The maximum time allowed time for each flip flop for a mod 10 synchronous counter if each flip flop delay is 25ns.
a) 25 ns
b) 50 ns
c) 100 ns
d) none

Q. The resolution for a DAC is given by 0.4% then no. of bits of DAC is
a) 8- bits
b) 16- bits
c) 32- bits
d) none

Ans: 8- bits

41) The chip capacity is 256 bits, then the no.of chips required to build 1024 B memory Is
a) 32
b) 16
c) 15
d) 4

Q. Which of the following are correct?
1)A flip-flop is used to store 1-bit of information
2)Race around condition occurs in JK flip flop when both the inputs are 1
3)Master slave flip flop is used to store 2 bits of information
4)A transparent latch consists of a D- flip flop

a) 1,2,3
b) 1,3,4
c) 1,2,4
d) 2,3,4

Ans: 1,2,4

Q. output resistance of ideal OP AMP is
a) 0
b) 1
c) infinite
d) very high

ANS: 0

Q. CMRR of an OP AMP is given as 80db and Ad is 20000.Value of Acm will be
a) 4
b) 8
c) 2
d) 1

Ans: 2

Q.Si,Ge lie in ……..block of periodic table
a) III
b) V
c) IV A
d) IV B

Ans: IV A

Q.to obtain 10 mV resolution on 5 V range how many bit DAC is to be used
a) 4
b) 8
c) 16
d) 32

Q.% resolution of a 10 bit ADC
a) 1.588%
b) 0.392%
c) 0.0978%
d) 0.0244%

Ans: 0.0978%

Q.Efficiency of half wave rectifier
a) 45%
b) 50%
c) 86%
d) 100%

__________________
Answered By StudyChaCha Member

HPCL placement team organised the exam for Electrical engineers . I’m a engineering student with Electrical stream. I want some
Question paper that are giving me some idea for placed in HPCL??

HPCL is one of the major integrated oil refining and marketing companies in India. It is a Mega Public Sector Undertaking (PSU) with Navaratna status. It’s consist fortune of 500 company in India. they conduct the Placement paper for Electrical engineers.

Here I’m providing you HPCL part =1 Qustion paper with answer:

HPCL PART - I TYPICAL QUESTIONS & ANSWERS OBJECTIVE TYPE QUESTIONS
Q.1 The two windings of a transformer is
(A) conductively linked.
(B) inductively linked.
(C) not linked at all.
(D) electrically linked.
Ans : B

Q.2 A salient pole synchronous motor is running at no load. Its field current is switched off. The motor will
(A) come to stop.
(B) continue to run at synchronous speed.
(C) continue to run at a speed slightly more than the synchronous speed.
(D) continue to run at a speed slightly less than the synchronous speed.
Ans: B

Q.3 The d.c. series motor should always be started with load because
(A) at no load, it will rotate at dangerously high speed.
(B) it will fail to start.
(C) it will not develop high starting torque.
(D) all are true.
Ans: A

Q.4 The frequency of the rotor current in a 3 phase 50 Hz, 4 pole induction motor at full load speed is about
(A) 50 Hz.
(B) 20 Hz.
(C) 2 Hz.
(D) Zero.
Ans: C

Q.5 In a stepper motor the angular displacement
(A) can be precisely controlled.
(B) it cannot be readily interfaced with micro computer based controller.
(C) the angular displacement cannot be precisely controlled.
(D) it cannot be used for positioning of work tables and tools in NC machines.
Ans: A

Q.6 The power factor of a squirrel cage induction motor is
(A) low at light load only.
(B) low at heavy load only.
(C) low at light and heavy load both.
(D) low at rated load only.
Ans: A

Q.7 The generation voltage is usually
(A) between 11 KV and 33 KV.
(B) between 132 KV and 400 KV.
(C) between 400 KV and 700 KV.
(D) None of the above.
Ans: A

Q.8 When a synchronous motor is running at synchronous speed, the damper winding produces
(A) damping torque.
(B) eddy current torque.
(C) torque aiding the developed torque.
(D) no torque.
Ans: D

Q.9 If a transformer primary is energised from a square wave voltage source, its output voltage will be
(A) A square wave.
(B) A sine wave.
(C) A triangular wave.
(D) A pulse wave.
Ans: A

Q.10 In a d.c. series motor the electromagnetic torque developed is proportional to
(A)1a
(B)12a-Answer
(C)1/1a
(D)1/12a
Ans: B

Q.11 In a 3 – phase induction motor running at slip ‘s’ the mechanical power developed in terms of air gap power Pg is
(A)(s-1)Pg
(B)Pg/1-S
(C)1-SPg-Answer
(D)S.Pg.


Q.12 In a 3 – phase induction motor the maximum torque
(A) is proportional to rotor resistance
(B) does not depend on
(C) is proportional to
(D) is proportional to

Q.13In a d.c. machine, the armature mmf is
(A) stationary w.r.t. armature.
(B) rotating w.r.t. field.
(C) stationary w.r.t. field.
(D) rotating w.r.t. brushes.
Ans: C

Q.14In a transformer the voltage regulation will be zero when it operates at
(A) unity p.f.
(B) leading p.f.
(C) lagging p.f.
(D) zero p.f. leading.
Ans: B

Q.15 The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be
(A) 3.6 V.
(B) 2.5 V.
(C) 3.0 V.
(D) 6.0 V.
Ans: C

Q.16 The emf induced in the primary of a transformer
(A) is in phase with the flux.
(B) lags behind the flux by 90 degree.
(C) leads the flux by 90 degree.
(D) is in phase opposition to that of flux.
Ans: C

Q.17 The relative speed between the magnetic fields of stator and rotor under steady state operation is zero for a
(A) dc machine.
(B) 3 phase induction machine.
(C) synchronous machine.
(D) single phase induction machine.
Ans: all options are correct

Q.18 The current from the stator of an alternator is taken out to the external load circuit through
(A) slip rings.
(B) commutator segments.
(C) solid connections.
(D) carbon brushes.
Ans: C

Q.19 A motor which can conveniently be operated at lagging as well as leading power factors is the
(A) squirrel cage induction motor.
(B) wound rotor induction motor.
(C) synchronous motor.
(D) DC shunt motor.
Ans: C


Q.20 A hysteresis motor
(A) is not a self-starting motor.
(B) is a constant speed motor.
(C) needs dc excitation.
(D) can not be run in reverse speed.
Ans: B

Q.21 The most suitable servomotor for low power applications is
(A) a dc series motor.
(B) a dc shunt motor.
(C) an ac two-phase induction motor.
(D) an ac series motor.
Ans: B

Q.22 The size of a conductor used in power cables depends on the
(A) operating voltage.
(B) power factor.
(C) current to be carried.
(D) type of insulation used.
Ans: C

Q.23 Out of the following methods of heating the one which is independent of supply frequency is
(A) electric arc heating
(B) induction heating
(C) electric resistance heating
(D) dielectric heating
Ans: C

Q.24 A two-winding single phase transformer has a voltage regulation of 4.5% at full-load and unity power-factor. At full-load and 0.80 power-factor lagging load the voltage regulation will be
(A) 4.5%.
(B) less than 4.5%.
(C) more than 4.5%.
(D) 4.5% or more than 4.5%.
Ans: C

__________________
Answered By StudyChaCha Member