Go Back   2021-2022 StudyChaCha > StudyChaCha Discussion Forum > General Topics

  #1  
Old May 31st, 2014, 08:53 PM
Super Moderator
 
Join Date: Nov 2011
Default NTPC Electrical previous year placement papers

Will you please give me the National Thermal Power Corporation Electrical previous year placement papers as it is very urgent for me?

As you want to get the National Thermal Power Corporation Electrical previous year placement papers so here is the information of the same for you:

1. Expression for d(n): u(n)-u(n-1)/ u(n-1)-u(n+1)/ u(n)+u(n+1)/…

2. Numerical on a photodiode: to calculate the responsivity/sensitivity when a specified no of incident photons cause a specified no of electron generation.

3. For a radioactive sample which decays to 12.5% of its initial value in x days, the half life is given by..

4. Connect two 1o resistors in series, then connect two 1h inductors across one of the resistors such that the ckt looks like a 1o resistor in series with a ?-section of a resistor and two inductors. With the series resistance on the I/p side, calc the transfer function of this ckt

5. Ac signal conditioning is used for inductive and capacitive/resistive/piezoelectric transducers/all of the above.

6. Lower useful input limit of a transducer is determined by..

7. Air-cored inductors are used for low frequency/high frequency/equal frequency operations.

8. Given 4 pole-zero plots identify which one corresponds to the driving point impedance of a series resonant ckt.

9. Given four unit-circle plots identify the one corresponding to a bandpass filter.

10. The sequence (2,3,4,3) is circularly even/circularly odd/circularly zero/both circularly even and odd.

11. Z-transform of 3n u(n).

12. Match the following with their characteristics: led/lcd/nixie tube/optical fibre.

13. A 4 khz signal is sampled at thrice the nyquist rate and sent through a channel with error =1%. Calc the bandwidth of the channel.

14. Given an op-amp ckt obtain an expression for o/p voltage.

15. No. Of encirclements made about the origin of the nyquist plot of the open loop tf:1/[(s-1)(s+2)(s+3)].

16. Given a two port network in the form of a t find o/p admittance in terms of y-parameters.

17. For a repeater in a pcm cable identify the correct sequence of actions amongst threshold/equalization/etc.

18. O/p of a delta modulator when a ramp input is fed to it.

19. Steady state error with ramp I/p for a type-0 system.

20. Creeping occurs in energy meters bcoz…

21. Ultrasonic method of flow measurement cannot be used in liquids with air bubbles/has less attenuation in air compared to liquid-identify the false statement (if any) among these.

22. Major cause of losses in a fibre optic cable: dispersion/total internal refraction/presence of core and cladding/..

23. Which layer in the OSI model is concerned with printer buffering, etc: network/session/transport/..

24. Given some function f(j?) calculate its inverse ctft.

25. Relation between Laplace and z-transform: s=z/ s=ln z/ s=( ln z/t) /..

26. Maximum and minimum probability error among ask,psk,fsk,dpsk etc

27. Which of the following is a non linear modulation scheme: pam/qam/pcm/..?

28. Match the following functions: e-t , e-t + et, sin(pt) with causal and stable system, causal and unstable system, etc.

29. Given a ckt with a 50 o resistor in series between two voltage sources of 10 v and 5 v magnitude calc power delivered by 5 v source.

30. Laplace transform of e-3tu(t)+e2tu(-t).

31. Which photo detector has output affected by own intrinsic noise: pn/apd/pin/all.

32. Inverse Laplace transform of 1/s2[d/ds(e-3s/s)]

33. When I mode is added to proportional control system stability increases/ decreases/ steady state performance deteriorates/damping increases.

34. Reset control is another name for integral/derivative/proportional/… Control.

35. Time response of system having transfer function 625/(s2+25) will be of the form..

36. Given some transfer function calc the peak response time.

37. The nyquist sampling rate of the function [sin(at)/t]2 will be..

38. The feedback topology that results in increased I/p and o/p impedance is current series/voltage series/current shunt voltage shunt.

39. Numerical on cardiac output calculation given heart rate and volume per beat.

40. In an ecg instrumentation amplifier the differential gain is provided by 1st stage/2nd stage/mismatched resistors/output stage.

41. Repeat question 40 above for the classic 3-op amp instrument amplifier.

42. Emg signals are of the order of mv/v/µv/..

43. Computer assisted tomography is used for..

44. Numerical on electrostatic instrument, to calculate deflection given spring constant, torque etc.

45. To prevent loading of a ckt I/p impedance of a cro should bee high/low/inductive/capacitive.

46. Addition of a zero to a 2nd order underdamped system results in increase/decrease of rise time and increase/decrease of peak overshoot.

47. For pi ctrl we obtain improved bandwidth/improved steady state performance/ worsened steady state performance/
.
48. SNR of normal am system is comparable/3 db lower/3 db higher/6 db lower over dsb-sc and SSB system.

49. Which is an effective measure of the noise related performance of an amplifier: snr/noise ratio/thermal noise/shot noise?

50. Given baseband signal freq and carrier freq calc which of the freq given will not be present for conventional am.

51. Distinction between fm and pm at high frequencies.

52. Which of these has the least propagation delay rtl/ecl/i2l/cmos.

53 Switching speeds of CMOS is affected/unaffected by changes in supply voltage.

54. Which of these provides a measure of heart rate p/qrs complex/t/none of these.

55. Given a Circuit of a logarithmic amplifier you had to identify what ckt was it.

56. JFET can operate in depletion/enhancement/both/none of the above modes.

57. When a bjt operates in saturation the junctions are fwd biased/reverse biased/..

58. Bibo stability criterion implies that poles are within/outside/on the unit circle.

59. For faithful amplification of low amplitude signals the cut-off/active/saturation regions of a transistor is used.

60. Lissajous pattern of a signal rotates 36 times per minute. If the oscillator frequency is 560 KHz then the unknown freq is..

61. % Resolution of a 10 bit adc.

62. To obtain 10 mv resolution on 5 v range how many bit dac is to be used..

63. Why is lcd preferred to led.

64. How will 0.6973 be displayed on 10 v range of a 4 ½ digit multimeter.

65. Which of the following cannot be used for an automatic feedback temp ctrl system thermocouple/thermometer/ Thermistor /ic sensor.

66. Y(n)=x(-n+3) is an example of a linear/non linear and shift variant/invariant system.

67. The falling body method is used to determine viscosity/humidity/…

68. Which of these methods of viscosity measurement gives greatest accuracy falling body method/rotating cylinder method/both/..?

69. Some question on gas chromatography

70.A device having a rotor with 3 y-connected coils and a stator is likely to be a synchro/rvdt/control transformer/..

71. In a twisted ring counter the initial count is 1000. After the 4th clock pulse its state will be…

72. A 240 khz signal is given into a 3 bit binary ripple counter. The lowest o/p freq obtainable is…

73. For parity bit checking which of the following gates can be used xor/nand/or/xnor.

74. Why is a BJT called so..

75. Identify the expression for gauge factor of a strain gauge among the given options.

76. In a semiconductor strain gauge as tensile strain is applied what changes take place in the n and p areas..

77. How does a radioactive level gauging system work..

78. A capacitive transducer measuring level works on the principle of change in distance between plates/change in dielectric strength/..

79. For maximum power transfer in an ac circuit the condition to be satisfied is zl+zs=0/xl+xs=0/none of these/…where l and s refers to load and source resp.

80. Find the transfer function from a block diagram.

81. Synchronous ctrs are preferred to asynchronous ctrs bcoz they are faster/glitches at the output can be avoided/both/none of these.

82. The lissajous figure formed on an oscilloscope looks like the english figure of 8. If the vertical channel input is 1 khz the horizontal input freq is…

83. Ie=ic for a transistor in saturation/cutoff/active/both saturation and active regions.

84. Reproducibility of measurements is called accuracy/precision/linearity/none of these.

85. Which of these is not strictly a static characteristic accuracy/precision/tolerance/linearity.

86. The shunt coil in a q meter has resistance of the order of mo/o/ko/..

87. For measuring inductance of high q coils the bridge used is maxwell-wien/schering/..

88. Which of these measures inductance in terms of capacitance maxwell and hay/maxwell and schering/hay and schering/..

89. In a flip-flop with preset and clear inputs both are applied simultaneously/clear is cleared when preset is applied/preset is cleared when clear is applied/…

90. What happens when the ret instruction is encountered by 8085

91. A 1024*8 memory chip needs how many address lines..

92. What happens when the push instruction is encountered by 8051.

93. In fm relation between no of sidebands w.r.t. Modulating freq

94. Numerical on dpsk.

95. A multiplexer accepts input data and provides one output all the time/one output at a time/many outputs at a time/many outputs all the time.

96. Pulse modulation is essentially a process of multiplexing/…

97. Wave shape is altered by clipper/clamper/voltage doubler/amplifier.

98. 4 Signals of frequencies 100,100,200 and 400 hz are sampled at nyquist rate and sent through tdm on a channel.the bandwidth of the channel is..

99. Superposition can be applied to a ckt with initial conditions/non-linear ckt/..

100. Kelvin’s double bridge is used for the measurement of..

101. Which of these is not an active transducer thermocouple/solar cell/rtd/none of these.

102. Oscillator using positive feedback has gain of 0/8/undefined value
103. Wien bridge oscillator should initially have closed loop gain >3/<3/=3/..

104. Some question on gain margin and phase shift of a system.

105. Fourier series expansion of even function has sine terms only/cosine terms only/no odd harmonics/..

106. Full wave rectifier gives clean dc o/p/dc o/p with small ripple/positive half and inverted negative half of I/p as o/p.

107. Which of these values of ? Gives damped oscillations: 0/1/1.6/0.6

108. For a transformer of ratio 1:a and excited by a source v with impedances z1 and z2 on the primary and secondary side value of a for maxm power transfer should be..

109. Fourier transform of cos(?0t) is..

110. At t=0 the step response of a 1st order system is…

111. 555 Can be used as a monostable/astable/freq dividing ckt/all of these.

112. In a pt when the secondary is open ckted with the primary excited what will happen.

113. If a system is marginally stable then the nature of oscillations will be..

114. Linear encoders mostly use straight binary/bcd/gray code.

115. For an accelerometer working in displacement mode the ratio of forcing freq to natural freq should be

APTITUDE Section

Insert the missing number?

16, 33, 65, 131, 261, (....)
Ans: A

A. 523
B.521
C.613
D.721

The banker's discount on a bill due 4 months hence at 15% is Rs. 420. The true discount is:
Ans.A

A.Rs. 400
B.Rs. 360
C.Rs. 480
D.Rs. 320

3. A train passes a station platform in 36 seconds and a man standing on the platform in 20 seconds. If the speed of the train is 54 km/hr, what is the length of the platform?

A.120 m
B.240 m
C.300 m
D.None of these

4. If a person walks at 14 km/hr instead of 10 km/hr, he would have walked 20 km more. The actual distance travelled by him is:

A 50 km.
B.56 km
C.70 km
D.80 km

5. From a point P on a level ground, the angle of elevation of the top tower is 30º. If the tower is 100 m high, the distance of point P from the foot of the tower is:
A. 149 m
B.156 m
C.173 m
D.200 m

6. A alone can do a piece of work in 6 days and B alone in 8 days. A and B undertook to do it for Rs. 3200. With the help of C, they completed the work in 3 days. How much is to be paid to C?
A. Rs. 375
B.Rs. 400
C.Rs. 600
D.Rs. 800

7. How much time will it take for an amount of Rs. 450 to yield Rs. 81 as interest at 4.5% per annum of simple interest?
A. 3.5 years
B.4 years
C.4.5 years
D.5 years

8. What is the difference between the compound interests on Rs. 5000 for 1http://www.indiabix.com/_files/images/aptitude/1-div-1by2.gif years at 4% per annum compounded yearly and half-yearly?
A. Rs. 2.04
B.Rs. 3.06
C.Rs. 4.80
D.Rs. 8.30

9. In a certain store, the profit is 320% of the cost. If the cost increases by 25% but the selling price remains constant, approximately what percentage of the selling price is the profit?
A. 30%
B.70%
C.100%
D.250%

10. Three candidates contested an election and received 1136, 7636 and 11628 votes respectively. What percentage of the total votes did the winning candidate get?
A. 57%
B.60%
C.65%
D.90%

11. A is two years older than B who is twice as old as C. If the total of the ages of A, B and C be 27, the how old is B?
A.7
B.8
C.9
D.10

12. The average weight of 8 person's increases by 2.5 kg when a new person comes in place of one of them weighing 65 kg. What might be the weight of the new person?

A. 76 kg
B.76.5 kg
C.85 kg
D.Data inadequate

13. Out of 7 consonants and 4 vowels, how many words of 3 consonants and 2 vowels can be formed?

A.210
B.1050
C.25200
D.21400

14. Let N be the greatest number that will divide 1305, 4665 and 6905, leaving the same remainder in each case. Then sum of the digits in N is:
A. 4
B.5
C.6
D.8

15. If 35 + 125 = 17.88, then what will be the value of 80 + 65 ?
A. 13.41
B.20.46
C.21.66
D.22.35

16. A bag contains 2 red, 3 green and 2 blue balls. Two balls are drawn at random. What is the probability that none of the balls drawn is blue?
A. 10
B.21
C.11
D.57

17. If log 27 = 1.431, then the value of log 9 is:

A. 0.934
B.0.945
C.0.954
D.0.958

18. If 5a = 3125, then the value of 5(a - 3) is:
A. 25
B.125
C.625
D.1625

19. If 2994 ÷ 14.5 = 172, then 29.94 ÷ 1.45 = ?

A. 0.172
B.1.72
C.17.2
D.172

20. In a mixture 60 litres, the ratio of milk and water 2 : 1. If the this ratio is to be 1 : 2, then the quanity of water to be further added is:

A. 20 litres
B.30 litres
C.40 litres
D.60 litres

21. Select the related letter from the given alternatives: Q P R S : T U W V :: J I K L :------ ?
N M O P
M N PO
N M P O
M N O P

Contact Details:
National Thermal Power Corporation Limited
Mora, A-ntpc, Kawas,
Hazira Road, Aditya Nagar,
Choriyasi, Kawas,
Gujarat State Highway 168,
Ichchhapor,
Surat,
Gujarat 394510 ‎
0261 286 1426 ‎
India

Map Location:

Last edited by Aakashd; February 27th, 2020 at 01:48 PM.
Reply With Quote
Other Discussions related to this topic
Thread
Previous year NTPC Mechanical Engineering papers
NTPC Previous Year Placement Paper
Previous year placement papers of TCS
NTPC Trainee Chemist Exam previous year question papers
NTPC-HR papers of previous year
How to get TCS Previous Year Placement Papers
Previous year papers of HPCL (Electrical and Electronics)
Previous year placement papers of HCL
S A I L Previous year electrical question papers
NTPC Assistant Chemist Trainee post exam previous year question papers
D R D O previous year electrical question papers
B H E L previous year electrical question papers
CTS previous year placement papers
NTPC engineer trainees previous year question papers
IES Electrical Engineering previous year question papers
NTPC Previous year Question Papers for Electrical Engineering stream
IBM previous year placement papers
BEL placement previous year papers
Previous year question papers of IES Electrical
HCL Previous year Placement Papers






  #2  
Old October 19th, 2015, 12:51 PM
Unregistered
Guest
 
Default Re: NTPC Electrical previous year placement papers

I want to get the NTPC Electrical previous year placement papers for the preparation of exam so can you please provide me this?
Reply With Quote
  #3  
Old October 19th, 2015, 12:51 PM
Super Moderator
 
Join Date: Jun 2013
Default Re: NTPC Electrical previous year placement papers

As you need the NTPC Electrical previous year placement papers for the preparation of exam so here I am sharing this

1. What is causal system?

2. Shunt reactor is used in EHV transmission line for ?

3. 20w, 40W, & 200w lamps are connected to three phases if neutral wire breaks then which lamp will fuse first?
1) 20
2)40
3)200
4)three lamps will fuse together.

4. Synchronous machine can be operated at both lagging and leading power factor ?

5 What does synchronous speed mean?

6. Frequency of emf generated per rotation of rotor is equal to. ?

7. DC machine having wave winding is wounded as lap winding what will be the effect on emf generated ?

8. Which is remain unchanged in transformer action?

9. In transformer windings are connected.?

10. In general how transformer is rated?

11. What is given on the name plate of motor?
1) KW
2) KVA
3) output shaft power

12. Short circuit test of transformer gives what?

13. Transformer core are laminated for what purpose?

14. What is supply voltage for heavy industry ?
1) 33KV
2) 11KV
3) 132 KV
4) 66KV

15. Basic structure SCR as a two transistor i.e. how they are connected?

16. What is Triac?

17. System admittance is (G+jB) what is reactive power absorbed if the voltage is V KV?
(1)V (square)*B
(2) V (square)*g .

18. In series R-L circuit what is phase difference between the voltage drop across R and L?

19. Power factor is cosine (delta ) delta is the angle between
1) phase voltage phase current
2) Line voltage lone current
3) phase voltage line current
4) line voltage phase current.

20. Laplace of exp (-at)?

21. For series R-L-C circuit the load will be capacitive if the frequency is
1) greater than the resonant frequency
2) less than the resonant frequency

22. In Wiens bridge which circuit elements determine the frequency range?

23. What is the output if two booster having duty cycle K and (K-1) are connected in series?

24. If a DC shunt motor is loaded from unloaded condition what will be effect of on terminal voltage?

25. A second wire system having one pole one right half of the s-plane. When the system will be stable?

26. A system having repetitive pole what will be effect on the gain at the cross over frequency?

27. Hollow conductor is used to reduce corona loss how does it reduce the loss?

28. In DC machine how voltage is related to flux?

29. Nature of current and voltage in the armature and at the terminal in DC machine.

30. Motor acts on the principle of ..rule

31. Which instrument measure both ac and dc?

32. How the rotation of induction motor is reversed?

33. If 3-phaseof a 3- phase balance load are reversed what will be the effect on the line current?

34. If the rating of VAR absorber is 50M VAR at 400KV. What will the VAR absorbed by the absorber at 300KV?

35. In regenerative breaking of DC series motor what is done?
__________________
Answered By StudyChaCha Member
Reply With Quote
Reply


Reply to this Question / Ask Another Question
Your Username: Click here to log in

Message:
Options



All times are GMT +6.5. The time now is 07:26 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions, Inc.
Search Engine Friendly URLs by vBSEO 3.6.0 PL2

1 2 3 4 5 6 7 8