KPCL Previous Paper

Give me question paper for the recruitment examination organizes by Karnataka Power Corporation Ltd.. ??

Here I am giving you question paper for the recruitment examination organizes by Karnataka Power Corporation Ltd..

KPCL Mechanical Question Paper for Assistant and Junior Engineer
The chronological order of strokes in a four stroke petrol engine is:
1] Suction stroke, working stroke, compression stroke and exhaust stroke.
2] Suction stroke, compression stroke, working stroke and exhaust stroke.
3] Compression stroke, working stroke, suction stroke and exhaust stroke.
4] Compression stroke, suction stroke, working stroke and exhaust stroke.

The enthalpy of steam is defined as:
1] Difference of internal energy and product of pressure and volume.
2] Product of internal energy and pressure.
3] Sum of internal energy and product of pressure and volume.
4] Amount of heat change divided by the absolute temperature.

Which of the following operations can be performed using a drilling machine?
A. Reaming B. Countersinking C. Spot Facing D.
Thread tapping
1] Only A, B and D 2] Only B, C and D 3] Only A, B and C 4] All of
these

Which of the following are the advantages of impulse turbine over reaction turbines?
A. Occupies less space per unit power.
B. Compounding is not necessary for speed reduction as the rotor speeds are usually low.
C. Suitable for high power generation.
1] B and C only 2] A only 3] C only 4] A and C only

Maximum power transfer through line V1= 110 kv, V2= 100kv, X=22 ohm is
a 500 MW
b 500 KW
c 250 MW
d 250 KW
Ans: 500 MW

Q.Which type of power plant requires maximum expenditure
a Hydel power plants
b Nuclear power plants
c Thermal power plants
d Gas based power plants

Q.Base load of a power station stands for
a 2-4 hours/day
b 4-8 hours/day
c 8-12 hours/day
d 12-24hours/day
Ans: 12-24hours/day

Q.A wire is placed on the top of a transmission line to protect from
a surge high voltage
b Direct lightning strocks
c indirect lightnin strocks
d Switching over voltages
Ans: Direct lightning strocks

Q.A wire is placed on the top of a transmission line acts as
a acts as a phase wire
b acts as neutral
c acts as a transmission wire
d acts as ground wire

Which of the following can be magnified by magnetic amplifier
(a) voltage
(b) current
(c) power
(d) none of above

The inductance is not used in lag network because of
(a) big size
b) time delay and hysteresis losses
(c) high reactance
(d) none of these

Saturation in a stable control system can cause
(a) conditional stability
(b) over damping
(c) low level oscillations
(d) high level oscillations

Excessive noise in control systems can cause
a) reduction in bandwidth
(b) reduction in gain
(c) saturation in amplifying stages
(d) oscillations

The type-0 system has
(a) net pole at the origin
(b) no pole at the origin
(c) simple at one origin
(d) two poles at the origin

In control systems, excessive bandwidth should be avoided because
(a) noise is proportional to bandwidth
(b) it leads to low relative stability
(c) it leads to slow speed of response
(d) none of these

Attached Files Available for Download

	Karnataka Power Corporation Ltd paper.doc (34.5 KB, 140 views)
	Karnataka Power Corporation Ltd paper 1.doc (30.0 KB, 142 views)

Please provide Karnataka Power corporation Limited Assistant and Junior Engineer exam paper???

You need Karnataka Power corporation Limited Assistant and Junior Engineer exam paper, I am giving here:

1. A 1.6 m3 capacity tractor loaded works at a site with an effective per-round-trip time of 64 seconds. Effective delivery of
excavated material is 90%. If utilization is 50 minutes per hour working, what will be the productivity in a 4-hour shift?
(a) 253 m3
(b) 262 m3
(c) 270 m3
(d) 282 m3
Ans. (c)

2. Match List-I with List-II and select the correct answer using the code given below the lists:
List-I List-II
(Equipment) (Category)
A. Derrick crane 1. Excavating equipment
B.Hoe 2. Hauling equipment
C. Clamshell 3. Hoisting ‘equipment
D. Dumper Truck 4. Vertical lifting equipment
Code:
A B C D
(a) 2 1 4 3
(b) 3 1 4 2
(c) 2 4 1 3
(d) 3 4 1 2
Ans. (b)

3. A 1.75 m3 capacity tractor loader has forward loaded speed of 240 m/min, returning unloaded speed of 300 m/min and operates at
80% of the specified speed. It hauls earth over a distance of 60 m with fixed time per trip being 25 seconds. What is its effective
cycle time?
(a) 54.25 seconds
(b) 55.50 seconds
(c) 56.75 seconds
(d) 58.75 seconds
Ans. (d)

4. Which one of the following relates to determination of critical path in PERT?
(a) Event oriented slack
(b) Activity oriented float
(c) Event oriented float
(d) Activity oriented slack
Ans. (a)

5. In order to achieve a safe compressive strength of 20 kg/cm2 in a brick masonary, what should be the suitable range of crushing
strength of bricks?
(a) 35kg/cm2 to 70 kg/cm2
(b) 70 kg/cm2 to 105 kg/cm2
(c) 105 kg/cm2 to 125 kg/cm2
(d) More than 125 kg/cm2
Ans. (b)

6. What is the requirement of water (expressed as % of cement w/w) for the completion of chemical reactions in the process of
hydration of OPC?
(a) 10 to 15%
(b) 15 to 20%
(c) 20 to 25%
(d) 25 to 30%
Ans. (c)

7. Which factors comprise maturity of concrete?
(a) Compressive strength and. flexural strength of concrete /
(b) Cement content per cubic metre and compressive strength of concrete
(c) Curing age and curing temperature of concrete
(d) Age and aggregate content per cubic metre of concrete
Ans. (c)

8. What is the minimum value of individual tests results (in N/mm2) for compressive strength compliance requirement for concrete
M20 as per codal provision?
(a) fck 1
(b) fck 3
(c) fck 4
(d) fck 5
Ans. (c)

9. For what reason is it taken that the nominal maximum size of aggregate may be as large as possible?
(a) Larger the maximum size of aggregate, more the cement required and so higher the strength.
(b) Larger the maximum size of aggregate, smaller is the cement requirement for particular water cement ratio and so more
economical the mix.
(c) Larger the maximum size of aggregate, lesser are the voids in the mix and hence also lesser the cement required.
(d) Larger the maximum size of aggregate, more the surface area and better the bond between aggregates and cement, and so higher
the strength.
Ans. (d)

10. What is the modulus of elasticity of standard timber (Group B) in (MN/cm2)?
(a) 0.5 to 1.0
(b) 1.0 to 1.25
(c) 1.25 to 1.5
(d) 1.5 to 1.75
Ans. (b)
11. What is the treatment for making timber fire- resistant?
(a) ASCU treatment
(b) Abel’s process
(c) Creosoting
(d) Tarring
Ans. (b)

12. How is the process of treatment of wood using a preservative solution and forcing air in at pressure designated?
(a) Ruping process
(b) Lawri process
(c) Full cell process
(d) Empty cell process
Ans. (d)

13. Modular bricks are of nominal size 20 × 10 × 10cm and 20% of the volume is lost in mortar between joints. Then what is the
number of modular bricks required per cubic meter of brick work?
(a) 520
(b) 500
(c) 485
(d) 470
Ans. (d)

14. A solid metal of uniform sectional area throughout its length hangs vertically from its upper end. Devails of the bar are:
length = 6m, material density = 8 × 10-5 N/mm3 and B =2 × 1o5 N/mm2. What will be the total elongation of the bar in mm?
(a) 288/104
(b) 48/104
(c) 144/104
(d) 72/104
Ans. (d)

15. What is the representative geometric mean size of an aggregate sample if its fineness modulus is 3.0?
(a) 150 µm
(b) 300 µm
(c) 600 µm
(d) 12 µm
Ans. (c)

16. A square steel bar of 50 mm side and 5m long is subjected to a load where upon it absorbs a strain energy of 100 J. What is
its modulus of resilience?
(a) 1/125 Nmm/ mm3
(b) 125 mm3/Nmm
(c) 1/125 Nmm/ mm3
(d) 100 mm3/Nmm
Ans. (a)

17. What is the ratio of flexural strength (fcr) to the characteristic compressive strength of concrete (fck) for M25 grade concrete?
(a) 0.08
(b) 0.11
(c) 0.14
(d) 0.17
Ans. (c)

18. Which of the following tests compares the dynamic modulus of elasticity of samples of concrete?
(a) Compression test
(b) Ultrasonic pulse velocity test
(c) Split test
(d) Tension test
Ans. (b)

19. Which one of the following is correct regarding the most effective requirements of durability in concrete?
(a) Providing reinforcement near the exposed concrete surface
(b) Applying a protective coating to the exposed concrete surface
(c) Restricting the minimum cement content and the maximum water cement ratio and the type of cement
(d) Compacting the concrete to a greater degree.
Ans. (c)

20. What is the radius of Mohr’s circle in case of bi-axial state of stress?
(a) Half the sum of the two principal stresses
(b) Half the difference of the two principal stresses
(c) Difference of the two principal stresses
(d) Sum of the two principal stresses
Ans. (b)

21. A square beam laid flat is then rotated in such a way that one of its diagonal becomes horizontal. How is its moment capacity
affected?
(a) Increases by 41.4%
(b) Increases by 29.27%
(c) Decreases by 29.27%
(d) Decreases by 41.4%
Ans. (d)

22. A timber beam is 100 mm wide and 150 mm deep. The beam is simply supported and carries a central concentrated load W. If the
maximum stress in shear is 2 N/mm2, what would be the corresponding load W on the beam?
(a) 20 kN
(b) 30 kN
(c) 40 kN
(d) 25 kN
Ans. (c)

23. A 40 mm diameter shaft is subjected to a twisting moment M2. If shear stress developed in shaft is 5 N/mm2,.What is the value of
the twisting moment?
(a) 628.8 Nm
(b) 328.4 Nm
(c) 62.8 Nm
(d) 30.4 Nm
Ans. (c)

24. A fixed end beam of uniform cross-section is loaded uniformly throughout the span. What is the proportion of the bending
moment at the centre to the end moment considering only elastic conditions?
(a) 1 : 1
(b) 1 : 2
(c) 1 : 4
(d) 2 : 3
Ans. (b)

25. Steel of yield strength 400 MPa has been used in a structure. What is the value of the maximum allowable tensile strength?
(a) 240 MPa
(b) 200 MPa
(c) 120 MPa
(d) 96 MPa
Ans. (a)

__________________
Answered By StudyChaCha Member

sir pls send the pervious years question papers for junior engineer(electrical)