Sir I am taking participate in the common entrance test for Karnataka Technical Board Diploma so I need it syllabus so can you provide me its syllabus.

[Kesari]

Here I am giving you syllabus of the common entrance test for Karnataka Technical Board Diploma as below:-

Mathematics Paper Syllabus:
Algebra,
Logarithms,
Progressions,
Partial Fractions,
Mathematical Induction,
Equations,
Elements Of Number Theory and Congruencies,
Analytical Geometry and Calculus,
Coordinate Geometry, Permutations and Combinations,
Binomial Theorem,
Calculus and Trigonometry.

Physics Paper Syllabus:
Hydrostatics and Hydrodynamics,
Static,
Dynamics,
Heat, and Geometrical Optics.

Chemistry Paper Syllabus:

Kinetic Theory of Gases,
Chemical Bonding,
Electrochemistry,
Radioactivity,
Stochiometry,
Atomic Structure,
Organic Chemistry and Environmental Pollution.

Biology Paper Syllabus:
The syllabus of biology is divided into two the following parts:-
Botany,
Zoology

res,
Sir/Madam
I am also a diploma student, I need syllabus copy of BEEE E&CE DEPT 2008th batch. I am hoping that you will give me a better response to me with thanking your faithfully
KIRANGANESH

I need the Karnataka Technical Board Diploma Agriculture Engineering syllabus, can you provide me the same???

[Nilesh]

As you required for the Karnataka Technical Board Diploma Agriculture Engineering syllabus, here I am uploading a PDF file having the same. Following is the content of attachment:

Conduct an experiment to verify Ohm's law

Conduct an experiment to measure the power
and power factor in a 1-phase AC Circuit

conduct an experiment to measure the energy
consumed in a single phase AC systems
1-phase Energy Meter

Conduct an experiment to determine Voltage and
Current ratio of a given single phase transformer

Control of Single lamp from one place

Control of Single lamp and Three pin socket
independentely.

Control of Single lamp from two places independently
(Staircase wiring system)

Wiring up of a flourescent lamp

Wiring of meterboard using energymeter,MCB,
kitkat fuse unit and with a neutral link.

Start and reverse the direction of rotation of a Single phase
Induction Motor

Using a suitable starter, start and reverse the direction
of rotation of a three phase Induction Motor

Conduct an experiment to draw the
V-I characteristics of junction diode

Conduct an experiment to draw the
V-I characteristics of Zener Diode

Conduct an experiment to trace the
output waveforms of halfwave rectifier

Conduct an experiment to trace the
output waveforms of fullwave bridge rectifier

Conduct a suitable experiment to verify NOT, AND, OR,
NOR and NAND gates truth table

Remaining syllabus is in the attachment, please click on it………..

Principles of agricultural Engg

1. Q No. 1 is compulsory
2. Answer any TWO full questions from each section.

QNo1.
a) Fill in the blanks with appropriate word 5
i) The volume of a cylinder is given by -------------------
ii) In an open belt drive the driver and driven are rotating in -------------------- direction
iii) The property by virtue of which a material can be drawn in to thin wire is called-----
iv) The purpose of adding two or more metal in to a main metal is called------------------
v) In two stroke engine all operations are performed in -------- revolution of crank shaft

b) Write any five properties of copper. 5

SECTION I

QNo2.a) State and explain Simpson’s rule to measure areas of irregular shape. 5
b) One boundary of a plot of land is st- line 60m. long. The lengths of
Perpendicular offsets at 10m. intervals from this line to the curved boundary are as follows

Distance(m) 0 10 20 30 40 50 60
Length of offset(m) 0 16 28 36 40 42 43

Find the area of the plot. 10

QNo3.a) Name various types of power transmission systems 2
b) With a neat sketch explain the working of stepped cone pulley 5
c) A shaft runs at 80 rpm and drives another shaft at 150 rpm through
belt drive. The diameter of the driving pulley is 600mm. determine
the diameter of the driven pulley 8


QNo 4.a) Write the uses of i) bevel gear ii) Rack and pinion 2
b) Explain with a neat diagram the working of Epicyclic gear train 5
c) Two spur gears have a velocity ratio of 1/3. The driven gear has
72 teeth and rotates at 300 rpm. Calculate the number of teeth and the
speed of the driver. 8

SECTION II
QNo 5. a) Define the following mechanical properties of metals i) Hardness ii) Toughness
iii) Malleability 3
c) What is alloying? Mention the purposes of alloying. 5
d) Write the composition and uses of i) Stainless steel ii) Manganese steel 7

QNo6. a) Name the various types of cast iron. 3
b) What are the impurities in steel? Mention their effects. 5
c) Write the composition and uses of i) Nickel steel ii) HSS 7

QNo7. a) What is heat treatment? List the purposes of heat treatment. 6
b) Explain the following heat treatment processes i) Annealing ii) Tempering
iii) Cyaniding 9

SECTION III

QNo8. a) Write any four properties and three uses of zinc 7
b) Write the composition, any two properties and one use of i) Montz metal
ii )bell metal 8

QNo9. a) Explain how IC engines are classified? 5
b) With a neat diagram explain the working of two stroke petrol engine. 8
c) What is detonation? Explain 2

QNo10. a) Write the composition, any two properties and one use of
i) Aluminum bronze ii ) Duralumin 8
b) With a neat diagram explain the working of simple carburetor 5
c) What is super charging? Explain. 2

QNo1.
a) Fill in the blanks with appropriate word 5
i) The volume of a cylinder is given by -------------------
ii) In an open belt drive the driver and driven are rotating in -------------------- direction
iii) The property by virtue of which a material can be drawn in to thin wire is called-----
iv) The purpose of adding two or more metal in to a main metal is called------------------
v) In two stroke engine all operations are performed in -------- revolution of crank shaft

b) Write any five properties of copper. 5

SECTION I

QNo2.a) State and explain Simpson’s rule to measure areas of irregular shape. 5
b) One boundary of a plot of land is st- line 60m. long. The lengths of
Perpendicular offsets at 10m. intervals from this line to the curved boundary are as follows

Distance(m) 0 10 20 30 40 50 60
Length of offset(m) 0 16 28 36 40 42 43

Find the area of the plot. 10

QNo3.a) Name various types of power transmission systems 2
b) With a neat sketch explain the working of stepped cone pulley 5
c) A shaft runs at 80 rpm and drives another shaft at 150 rpm through
belt drive. The diameter of the driving pulley is 600mm. determine
the diameter of the driven pulley 8

QNo 4.a) Write the uses of i) bevel gear ii) Rack and pinion 2
b) Explain with a neat diagram the working of Epicyclic gear train 5
c) Two spur gears have a velocity ratio of 1/3. The driven gear has
72 teeth and rotates at 300 rpm. Calculate the number of teeth and the
speed of the driver. 8

SECTION II
QNo 5. a) Define the following mechanical properties of metals i) Hardness ii) Toughness
iii) Malleability 3
c) What is alloying? Mention the purposes of alloying. 5
d) Write the composition and uses of i) Stainless steel ii) Manganese steel 7

QNo6. a) Name the various types of cast iron. 3
b) What are the impurities in steel? Mention their effects. 5
c) Write the composition and uses of i) Nickel steel ii) HSS 7

QNo7. a) What is heat treatment? List the purposes of heat treatment. 6
b) Explain the following heat treatment processes i) Annealing ii) Tempering
iii) Cyaniding 9

SECTION III

QNo8. a) Write any four properties and three uses of zinc 7
b) Write the composition, any two properties and one use of i) Montz metal
ii )bell metal 8

QNo9. a) Explain how IC engines are classified? 5
b) With a neat diagram explain the working of two stroke petrol engine. 8
c) What is detonation? Explain 2

QNo10. a) Write the composition, any two properties and one use of
i) Aluminum bronze ii ) Duralumin 8
b) With a neat diagram explain the working of simple carburetor 5
c) What is super charging? Explain. 2

[omkara123]

Sir can u please provide me karnataka diploma instrumentation & controll syllabus