Internship in BHEL

Can you provide me the procedure for doing internship in BHEL (Bharat Heavy Electricals Ltd)?

For applying for an internship in BHEL, one needs to get an approval from the institute in which you are studying. A letter of approval addressed to The General Manager, Human Resource Development Centre, and BHEL. One has to pay a fee of approx. Rs.500 per week for the training.

Terms and Conditions: To apply for training program in BHEL, candidate should follow below given conditions:

Take a look on official website of BHEL regarding selection and application procedure for internship.

One needs to read and understand the General Instruction of the Company.

Fill up the application form and submit it online

Company will inform about the date of written test and venue though an email or post

Selection Procedure:

Applicants need to appear for written exam conducted by BHEL

The Written test will be of objective type, in which 70% of weight age is for the technical subjects and 30% for the aptitude

Selected applicants will be called for the interview.

Final selection will be based on 75% for written test marks and 25% for interview marks.

Applicants are called for interview in 1:3 ratios.

Applicants of SC/ OBC/ST category will be consideration with their categories respectively.

Selected candidates are required to work wherever they are initially posted for a period of time.

Eligibility:
To apply for the training in BHEL, candidate must fulfill following conditions:

Passed full time Bachelor degree in Engineering or Technology from a recognized University/ Institute in India

Secure 65% or equivalent CGPA in aggregate of all semesters.

Age should not be more than 27 years

__________________
Answered By StudyChaCha Member

BHEL is one of the largest government organizations in India

The head office is located in Bhopal.

Procedure to apply:
For applying to internship in BHEL, firstly you have to get an approval from placement cell of your institute.

A letter of approval should be send to The General Manager, Human Resource Development Centre, and BHEL in the month of February.

You need to pay a fee of approx. Rs.500 per week for the training.

Eligibility:
To apply for the training in BHEL you have to fulfill these requirements

Must have passed Bachelor’s degree in Engineering or Technology in the discipline of Mechanical/Electrical/Electronics from recognized University with at least 65% or equivalent CGPA in all semesters

Age should not be more than 27 years

Selection Procedure:
You have to appear for written examination conducted by BHEL

Written test will be of objective type
70% of weight age for the technical subjects
30% for the aptitude

Students who cleared the written test will be called for the interview.

Final selection will be on the basis of
75% for written test marks
25% for interview marks

BHEL Exam Question Paper

1. The ratio of two specific heats of air is equal to. = 1.41
2. A perfect gas at 270C is heated at constant pressure till its volume is double. The final temperature
is = 3270C
3. An engine operates between temperature of 9000K and T2 and another engine between T2 and
8000K. For both to do equal work, value of T2 will be. = 6500K
4. Internal energy of a substance depends on = Temperature
5. Work done in compressing 1kg of gas adiabatically from p1,V1,T1 to p2, V2, T2 is equal to = Cv(T2‐T1)
6. The unit of entropy is = J/kg 0K
7. Indicated power of a 4‐stroke engine is equal to = pLAN/2
8. Which of the following is not an internal combustion engine : a) 2 stroke petrol engine b)4 stroke
petrol engine c) Diesel engine d) steam engine e) Gas turbine. = (d)
9. If one cylinder of a diesel engine receives more fuel than the others, then for that cylinder the: a)
exhaust will be smoky b) piston rings would stick into piston grooves c) exhaust temperature will be high
d) engine starts overheating e) all of the above. = (e)
10. The spark plug gap is normally maintained at: = 0.45 to 0.6mm
11. A distributor in spark ignition engines performs the function of : = Providing the correct firing order
in engine
12. Which of the following does not relate to C.I. engine:: a) fuel pump b) fuel injector c) governor d)
carburetor e) flywheel = (d)
13. Air fuel ratio in a jet engine is = 60:1
14. What is the value of Prandtl No.?
15. In domestic refrigerator, the tubes at the back of the refrigerator are: a) evaporator b) condenser c)
capillary tubes d)………
16. Which refrigerants has the highest critical point temperature. = Freon‐11

17. Wet bulb temperature is. = indication of amount of moisture in air
18. On psychrometric chart, dry bulb temperature lines are. = Vertical
19. Surface tension has the units. = newtons/m
20. The line of action of the buoyant force acts through the. =centroid of the displaced volume of fluid
21. A pressure of 25m of head of water is equal to. =245kN/m2
22. For a submerged body to be in stable equilibrium, the centre of gravity should be. =Below the centre
of buoyancy.
23. The actual velocity at vena contracta for flow through an orifice from a reservoir of height H=?.
=Cvv2gH
24. A body weighing 2kg in air weights 2.5kg when submerged in water. Its specific gravity is. = 6
25. In a free vortex motion: = each particle moves in a circular path with a speed varying inversely as the
distance from the centre.
26. A centrifugal pump has speed‐1000rpm, Flow‐1200l.p.m, Head‐20m, Power‐5H.P. If its speed is
increased to 1500rpm, new flow will be.: = 1800l.p.m
27. Runaway speed of a hydraulic turbine is: = the speed if the turbine runner is allowed to revolve
freely without load and with the wicket gates wide open.
28. 10m of water column is equal to = 100kN/m2
29. M.I. of a circular area about an axis perpendicular to the area is: = pr4/2
30. A projectile is fired at an angle ? to the vertical. Its horizontal range will be maximum when ? is .
=450
31. An elevator weighing 1000kg attains an upward velocity of 4m/sec in two seconds with uniform
acceleration. The tension in the supporting cables will be = 1200kg.
32. A 13m ladder is placed against a smooth vertical wall with its lower end 5m from the wall. What
should be the co‐efficient of friction between ladder and floor so that it remains in equilibrium. = 0.21
33. A car is moving with a velocity of 60km/hr and possesses energy of 5x105 joules. The mass of the car
will be. =3000kg.

34. If l is the span of a light suspension bridge whose each cable carries total weight (w) and the central
diop is y, the horizontal pull at each support is: = wl/y OR
35. A beam of length l, having uniform load w kg/unit length is supported freely at the ends. The
moments at mid span will be: = wl2/8. http://www.ChetanaS.org
36. A boiler shell 200cm dia and plate thickness 1.5cm is subjected to internal pressure of 1.5MN/m2,
then the hoop stress will be. = 100N/m2
37. 100KW is to be transmitted by each of two separate shafts. A is turning at 250rpm and B at 300rpm.
Which shaft must have greater diameter.: = B
38. Two identical leaf springs of spring constant k are arranged like cantilevers in parallel and attached
at free end by a spring of spring constant k. The equivalent spring constant of combination is; = 1.5k.
39. Automobile steering gear is an example of: = lower pair.
40. The type of coupling used to join two shafts whose axes are neither in same straight line nor parallel,
but intersect is. = Universal coupling.
41. To transmit power from one rotation shaft to another whose axes are neither parallel nor
intersecting, use: = Spiral gear.
42. A gear having 100 teeth is fixed and another gear having 25 teeth revolves around it, the centre lines
of both gears being joined by an arm. How many revolutions will be made by gear of 25 teeth for one
revolution of arm. = 5 rev.
43. The secondary critical speed of a shaft occurs at: = twice the speed of primary critical speed.
44. Brittle coating technique is used for: = experimental stress analysis.
45. Factor of safety is the ratio of: = yield stress/working stress.
46. Type of gear used for non‐intersection perpendicular shafts: = Hypoid gears.
47. Corrosion resistance of steel is increased by adding: = Chromium & Nickel
48. The product of Cupola is called: = cast iron
49. Brinell tester uses a hardness steel ball of size: = 10mm

50. Sintered and tungsten carbides can be machined by: = EDM
51. What kind of abrasive cut off wheel should be used to cut concrete, stone and masonry? =Diamond
grit.
52. In break‐even analysis, total cost consists of: = Fixed cost + Variable cost.
53. The amount deducted from the salary of workers towards employees provident fund is : =deposited
in the account of worker with Provident Fund Commissioner.
54. PERT is: = event oriented technique
55. Bar charts are suitable for: = minor works.
56. ? on a PERT/CPM chart represents: = a significant event representing some mile‐stone
57. Electron volt is the unit of : = Energy.
58. Seamless tubes are made by?
59. Reheating in gas turbine results in: = increase of work ratio and decrease of thermal efficiency.
60. Why DC current is not used in transformer?
61. What is the purpose of draft tube in hydraulic turbines: = to convert the kinetic energy into pressure
energy.
62. A mass of 100kg is falling from a height of 1m and penetrates the sand to 1m. what is the resistance
force of the sand?
63. Two cars travel in the same direction at 40km/hr at a regular distance. A car comes in the opposite
direction at 60km/hr. It meets each car in a gap of 8 seconds. What is the distance between the two
cars?

__________________
Answered By StudyChaCha Member