IES Exam Question papers

Here I am looking for the IES Civil Engineering Exam Question Paper of UPSC, can you please provide me the same???

The previous year General Studies question paper of Indian Engineering Services (IES) exam as your Brother needs it for preparation of this very important exam is as follows:

1. The notice reads: "Beware off this monkey, he has sudden bouts of anger."
No error. (a) (b) (c) (d)

2. The police entered into the house and questioned the head of the family
(a) (b) about the theft. No error. (c) (d)

3. ''Have vou seen any good films lately?" "Not since the last few month~."
No error. (a) (b) (c) (d)

4. Des""Jite all the information I had gathered, . I soon found that (a) (b) 1-'ery little was known about the. Palk Strait. No error. (c) (d)

5. =-Ie had tied the knot so lose that it gave way very soon. No error. (a) (b) (c) (d)

Attached Files Available for Download

IES exam question papers.pdf (992.1 KB, 19 views)

As you are looking for the IES Civil Engineering Exam Question Paper of UPSC, so here I am sharing the same with you

Which of the following statements is/are correct?
1. For statically determinate structures, magnitudes for maximum effects due to a series of concentrated loads can be established with the aid of influence lines.
2. Cables in suspension bridges will not take the parabolic shape if uniformly loaded along the horizontal span.
3. In a three-hinged arch structure,the normal force, shear and moment at any section are not influenced by the horizontal reaction at the support.
(a) 1, 2 and 3
(b) 1 only
(c) 2 only
(d) 3 only

Stiffness method of structural analysis starts with
(a) force-deformation relations
(b) equilibrium condition
(c) compatible deformation
(d) equilibrium state of internal stress components

For which one of the following cases is the Muller-Breslau principle applicable
to get influence line?
(a) Reaction at the ends of a simple beam
(b) Bending moment at a section
(c) Shear force at a section
(d) Forces and moments at any section

Consider the following statements:
1. The virtual work method is preferred to the equilibrium method for the determination of Collapse load in a structure.
2. The number of plastic hinges required for the total collapse of a statically indeterminate structure is one less than the degree of indeterminacy of the structure.
3. In a large system the uniformly distributed load can be replaced by a number of concentrated loads to simplify the plastic analysis. Which of these statements are
correct?
(a) 1, 2 and 3 (b) 1 and 2 only
(c) 1 and 3 only (d) 2 and 3 only

Rest of the Questions are attached in below file which is free of cost

Attached Files Available for Download

UPSC IES CE Question Paper.pdf (576.6 KB, 15 views)

__________________
Answered By StudyChaCha Member

I am going to participate in IES exam, so need previous question paper for preparation, please provide here?

This is the UPSC Indian Engineering Services exam topics for questions:

The entrance for Indian Engineering Service comprises of a Written Exam (section I and II) and an Interview. The details follow:
One Engineering Discipline should be chosen from the following categories:
Civil Engineering
Mechanical Engineering
Electrical Engineering
Electronics and Telecommunication Engineering

The written examination will comprise two sections:
Section I - objective types questions
Section II – conventional (essay) type questions papers.
Both Sections will cover the entire syllabus of the relevant engineering subject.

Question Paper:
Here is the attachment of the UPSC IES exam question paper:

Attached Files Available for Download

	UPSC IES Question paper.pdf (220.9 KB, 33 views)
	UPSC IES Question paper 1.pdf (419.7 KB, 30 views)

__________________
Answered By StudyChaCha Member

I am appearing in the IES exam. So can you provide me the question papers of IES ELECTRICAL Examination?

As you want to get the question papers of IES ELECTRICAL Examination, so here I am providing the following question papers:

IES ELECTRICAL Question Paper1

The content of the program counter of an Intel 8085A microprocessor specifies which one of the following?
a. The address of the instruction being executed
b. The address of the instruction executed earlier
c. The address of the next instruction to be executed
d. The number of instructions executed so far

In an Intel 8085A microprocessor, why is ready signal used?
a. To indicate to user that the microprocessor is working and is ready for use
b. To provide proper WAIT states when the microprocessor is communicating with a slow peripheral device
c. To slow down a fast peripheral device so as to communicate at the microprocessor’s speed
d. None of the above

Match List-I with List-II and select the correct answer using the code given below the lists:
List-I
(Semiconductor technology)
A. TTL
B. ECL
C. NMOS
D. CMOS
List II
(Characteristic)
1. Maximum power consumption
2. Highest packing density
3. Least power consumption
4. Saturated logic

Code:
A B C D
a. 1 4 2 3
b. 4 1 2 3
c. 1 4 3 2
d. 4 1 3 2

1. Consider the following statements:
When all the elements in one row of the
Routh’s tabulation are zero then this
condition indicates

1. one pair of real roots with opposite
sign in s-plane

2. one pair of conjugate roots on the
imaginary axis in s-plane

3. conjugate roots forming a quadrate in
s-plane
Which of the statements given above is/are
correct?
a. 1 only
b. 2 only
c. 3 only
d. l, 2 and 3

2. The low frequency and high frequency
asymptotes of Bode magnitude plot are
respectively -60 db/decade and -40
db/dccade. What is the type of the system?
a. Type 0
b. Type I
c. Type II
d. Type III

3. Which one of the following is correct?
If the open-loop transfer function has one
pole in the right half of s-plane, the closed
loop system will be stable if the Nyquist
plot of GH
a. does not encircle the (-1 + j0) point
b. encircles the (-1 + j0) point once iii the
counter-clockwise direction
c. encircles the (-1 + j0) point once in the
clockwise direction
d. encircles the origin once- in the
counter-clockwise direction

4. Which one of the following is correct?
The value of the system gain at any point
on a root locus can be obtained as a
a. product of lengths of vectors from the
poles to that point
b. product of lengths of vectors from mm
the zeroes to that point
c. ratio of product of lengths of vectors
from poles to that point to the product
of length of vectors from zeros to that
point
d. product of lengths of vectors from all
poles to zeros

5. Which one of the following is correct ?
The slope of the asymptotic Bode
magnitude plot is integer multiple of
a. ± 40 db/decade
b. ± 12 db/decade
c. ± 6 db/decade
d. ± 3 db/decade

6. What is the range of K for Which the open
loop transfer function 2 ( )
( )
K G s
s s a
=
+
represents an unstable closed loop system?
a. K > 0 only
b. K = 0 only
c. K < 0 only
d. - ∞ < K < ∞

7. The characteristic polynomial of a discrete
time system is given by z2 + z + a. For
what value of ‘a’ is the system stable ?
a. 2
b. 0.5
c. 1.5
d. -0.5

8. Isocline method is used for which one of
the following?
a. Design of nonlinear system
b. Construction of root loci of nonlinear
system
c. Construction of phase trajectories of
nonlinear systems
d. Stability analysis of non-linear system

9. To detect the position error in a position
control system, which of the following
may be used?
1. Potentiometers
2. Syncbros
3. LVDT
Select the correct answer using the code
given below:
a. 1 and 2 only
b. 1 and 3 only
c. 2 and 3 only
d. 1, 2and 3

10. Single step response of a typical stepper
motor is quite oscillatory. Brakes are used
to reduce or eliminate oscillations. Which
one of the following statements is not
correct regarding use of brakes?
a. It provides memory or position
information when motor is switched
off.
b. reduces deceleration time.
c. It reduces length of motor load.
d. It reduces pullout torque.

11. Synchro machines are used for which one
of the following?
a. Converting 1-phase supply to 3-phase
supply
b. Stepping up low frequency signal to
high frequency
c. Detection of positional error in a.c.
servo system
d. Detection of positional error in d.c.
servo system

12. A, B, C and D represent the transmission
parameters of a two-port network. When is
the network reciprocal?
a. AB - CD = 1
b. AD - BC = 1
c. AB - CD = 0
d. AD – BC = 0

13. Match List I with List II and select the
correct answer using the code given below
the lists;
List-I
(Network parameter)
A. h11
B. h12
C. h22
D. h21
List-II
(Dimension)
1. Impedance
2. Admittance
3. Current ratio
4. Voltage ratio
Code:
A B C D
a. 2 4 1 3
b. 2 3 1 4
c. 1 3 2 4
d. 1 4 2 3

15. Which one of the following passive
components has the most precise and
accurate standard ?
a. Resistance
b. Inductance
c. Capacitance
d. Conductance.

16. Which of the following is/are primary
standard(s) for voltage maintained by
National Standards Laboratories?
1. Zener diode with 1.5 V output at 20°C
2. Nickel cadmium rechargeable cell of
1.25 V output at 20 °C
Select the correct answer using the code
given below:
a. 1 only
b. 2 only
c. Both 1 and 2
d. Neither 1 nor 2

To get full paper, download the file…………………….

Attached Files Available for Download

	IES ELECTRICAL Question Paper 1.pdf (599.0 KB, 40 views)
	IES ELECTRICAL Question Paper 2.pdf (579.9 KB, 26 views)

__________________
Answered By StudyChaCha Member

Can you provide me previous year General Studies question paper of Indian Engineering Services (IES) exam as my Brother needs it for preparation of this very important exam?