2023-2024 StudyChaCha

#1
May 4th, 2013, 12:50 PM
 Unregistered Guest
AAI Question Papers Model

Hey let me provide me AAI Question Papers
 Other Discussions related to this topic Thread

#2
May 6th, 2013, 09:50 AM
 Senior Member Join Date: Apr 2013
Re: AAI Question Papers Model

AAI Selection Procedure for the pos JE( ELECTRONICS). Test consists of total 100 questions.

Paper pattern:-

The paper consists of General Aptitude, Reasoning, GK,and Technical questions.

Type of Exam : Objective

Time limit-2 hours

No of Questions :100

some model questions from technical section is as given below -

1. In a communication system, noise is most likely to affect the signal
(a) at the destination
(b) In the channel
(c) in the information source
(d) at the transmitter
2. Indicate the false statement. Fourier analysis shows that the saw tooth
wave consist of
(a) fundamental and subharmonic sine waves
(b) a fundamental sine wave and an infinite number of harmonics
(c) fundamental and harmonic sine waves whose amplitude decreases with
the harmonic number
(d) sinusoidal voltages, some of which are small enough to ignore in
practice
3. One of the following types of noise becomes a great importance at high
frequencies. Is the
(a) random noise
(b) shot noise
(c) impulse noise
(d) transit-time noise
4.Indicate the false statement. The square of the thermal noise voltage
generated by a resistor is proportional to
(a) its temperature
(b) Its resistance
(c) Boltzmann’s Constant
(d) the bandwidth over which it is measured
5.If the plate supply voltage for a plate modulated class C amplifier is V, the
maximum plate-cathode voltage could be almost as high as
(a)4v
(b)3v
(c)2v
(d)1v
6. Which one will be stable if characteristics equation is
(a) AS^2+BS+C
(b) AS^2-BS-C
(c) AS^4+BS^2+CS+D
(d) -AS^2+BS-C
7.When microwave follows curvature of the earth, this I know as
(b) Ducting
(c) troposphere scatter
(d) ionosphere reflection
(a) telegraph cables
(b) repeater amplifiers
(d) Geostationary satellites
9. Switching systems
(a) Improve the efficiency of data transfer
(b) are not used in data system
(d) are limited to small data networks
10. Basic group B
(a) occupies the frequency range from 60 to 108 k hz
(b) consist of erect channels only
(c) is formed at the group translating equipment
(d) consist of five super group
11. In differential amplifiers, the common emitter current is made constant
(a) To make Ad (differential gain) very small
(b) To make Ac (common mode gain) very small
(c) To make the amplifier symmetrical
(d) To keep CMRR constant
12. Given BCD number 1001 0011, its decimal equivalent is
(a) 147
(b) 143
(c) 93
(d) 39
13. An amplifier has voltage gain of 50. this gain in db will be
(a) 17 db
(b) 31 db
(c) 34 db
(d) 68 db
14. In a E plane Tee, the output of the two rams are
(a) 180 degree out of phase
(b) In the same phase
(c) 90 degree out of phase
(d) none of these
15. waveguide are generally made of
(a) Aluminium
(b) Bronze
(c) Both (a) and (b)
(d) none of these

1.(b) 2.(a) 3.(d) 4.(a) 5.(a) 6.(a) 7.(b) 8.(b) 9.(a) 10.(a) 11.(b) 12.(c) 13.(c) 14.(a) 15.(c)
#3
February 20th, 2015, 11:22 AM
 Super Moderator Join Date: Nov 2011
Re: AAI Question Papers Model

You need Airports Authority of India exam model question paper, here I am giving:

1. 16QAM b. 16PSK c. QPSK

2. Same Antenna is used for Tx and Rx. Radar range related to Antenna gain as
1. Directly prop. To G
2. Direc. Prop. To sq. root of G
3. Inversely prop to G

3. Thermal Noise in conductor related to B
1. B
2. 1/B
3. B2
4. Square root of B

4. A control system with feed back gain 0.1 and forward gain 10. What is the sensitivity of the system w.r.t the feed back system.

5. The value of ‘k’ for the system to be stable is. ( 6th degree Characteristic Eqn given)

6. Which of the following system is stable.
1. As2 + Bs +C
2. As2 – Bs +C
3. As4 + B s3 +Cs+D
4. -As2 – Bs -C

7. Linux OS based on which architecture

8. Comparison betweeb Macro and Subroutine
1. Macro better that Sub Rtne with respect to storage time and execution time
2. Vice versa
3. Macro better that Sub Rtne with respect to execution time only
4. Vice versa

9. Which of the following is a privileged instruction?
1. MOV A B
2. INT 21
4. IN 08

10. Which of the following instruction is not converted to binary by an Assebly Language Program?
1. TRAP
2. Interrupt
3. Privilige instruction
4. Sorry don’t remember

11. In which type of machine can multiple tasks be done
1. Virtual Machine
2. Sorry don’t remember

12. Which of the following has the highest distortion?
1. A
2. B
3. AB
4. C

13. Which of the following distortions occur in Class B push pull amplifier?
1. Harmonic
2. Intermodulation
3. Phase
4. Sorry don’t remember

14. ?(s)/T(s) of a rotational system (J,B,k regular notaions)

15. Schmitt Trigger with 3V & 1V UTP and LTP respectively. A sinusoidal input with 10V peak is fed as the input. The output swings between

16. Op-amp circuit given. Identify the circuit (Ans: Peak detector)

17. 6 bit binary ladder with 101001 as input ( 0= 0V , 1 = 10V). Output voltage is ——

18. Doppler Radar of 1125 MHz. Frequency of received echo is 125 MHz. The conclusion is
1. Target also has a radar
2. Target moving away
3. Target approaching

19. Microprocessor cycles between
1. Fetch and Execution operations.
2. Fetch and Halt

20. Modulation index of an FM system with 2.5V, 500 Hz input and 5KHz deviation is

21. Routh’s Criterion gives
1. Number of roots on the LHS of S plane
2. Number of roots on the RHS of S plane

22. For the system to be stable, the roots of the characteristic Equation must lie
1. Left side of the S plane
2. Right side of s plane

23. Impulse response h(t) of a system is
1. Inverse Laplace transform of Transfer Function

24. The output of a LTI system with Guassian process input is
1. Gaussian
2. Poisson

25. Spectral Density and Auto-Correlation are
1. Laplace Transform pair
2. Fourier Transform Pair.

26. A flex Klystron is a
1. Microwave amp
2. Microwave Oscillator
3. Both amp and Oscillator
4. High cavity tube

27. S Matrix related question.

28. Block diagram given

Oscillator(1MHz) à Divider (/ 10^6) à Schmitt Trigger à Flip Flop à. Output is

1. Pulse Train of width 1 sec
2. Pulse Train of width 2 sec
3. Pulse Train of width 0.5 sec
__________________

 Tags model papers