Go Back   2021-2022 StudyChaCha > StudyChaCha Discussion Forum > General Topics

  #2  
Old March 17th, 2012, 10:46 AM
diwakargautam
Guest
 
Default NIMS answer key 100a

what is NIMS answer key 100a? From where can I get information about NIMS answer key 100a?
Reply With Quote
  #3  
Old March 19th, 2012, 08:26 PM
ashishloyal
Guest
 
Default NIMS answer key to is 700

Sir, please provide me NIMS 700 answer key or give me website name from where can I download NIMS 700 answer key?
Reply With Quote
  #4  
Old March 20th, 2012, 10:54 AM
shaik shahina
Guest
 
Default NIMS Answer Key 700a

Please give me NIMS answer key of 700a? please provide me answer key in pdf format for save answer key in PC?
Reply With Quote
  #5  
Old March 2nd, 2013, 01:09 PM
Super Moderator
 
Join Date: Dec 2011
Default Re: NIMS Answer Key

As per you are asking for question paper of NIMS so here we are sharing some of questions given here:

20) A surface finish symbol is as follows: 15

a) The surface finish is 0.015 inches
b) The surface finish is finer than a callout of 10
c) The surface finish is 15 millimeters
d) The surface finish is rougher than a callout of 25
e) The surface finish is 15 micro inches

21) What is the most common type of surface finish callout?

a) Roughness
b) Waviness
c) Cut band length
d) Lay


Inspection Plan and Sampling Procedures

• Initial step for developing an inspection plan

• Main criteria for determining when a part is rejected

• Definition of a sampling

• Rationale for having inspection plans

• Main detail for determining the correct measuring tool to check a dimension

• The contribution of the sampling plan to quality control


22) A part is considered a reject when:

a) All the dimensions are in tolerance
b) Dimensions are out of tolerance
c) The daily production rate is not achieved
d) The part fails to be inspected in an 8-hour shift

23) A sampling is referred to as a:

a) Total population of parts
b) Number of defects in a shift
c) Samples taken from a machine over a period of time
d) The number of parts that meet all dimensions

24) Inspection plans are needed to:

a) Coordinate inspection procedures
b) Identify measuring tools
c) Check dimensions in a repeatable and reliable way
d) All of the above
e) Only a and c

25) The first thing to do when constructing an inspection plan is to:

a) Check the machine tool for accuracy
b) Select the critical and important dimensions to inspect
c) Select the measuring instruments
d) Construct SPC charts for all dimensions

26) The most important factor in selecting measuring tools for inspection is:

a) Access to measuring equipment
b) Process capability of the part in assembly
c) Tolerancing of dimensions to inspect
d) Verification of the sampling plan

27) Sampling plans contribute to a quality control process by:

a) Providing an acceptable representation of all the parts produced
b) Providing a list of acceptable measuring tools
c) Defining tolerances regardless of the print tolerances
d) Creating error margins in capability ratios

Measuring Techniques and Tools

• Application of a sine bar for checking angles

• Feature of a thread checked by a thread micrometer

• Application of gage pins for checking diameters

• Feature best suited for measuring with a dial bore gage

28) What feature of a thread is checked with a thread micrometer?

a) Major diameter
b) Minor diameter
c) Crest radius
d) Root radius
e) Pitch diameter

29) Dial bore gages are used to measure:

a) Tapered shafts
b) Internal threads
c) Holes
d) Bosses and pads

30) To indicate an angled surface and make that surface parallel to a surface plate, the machinist would use a __________.

a) Angle plate and plate protractor
b) Sine plate
c) Machinist vise
d) V-block and indicator

31) What sizes of gage pins would a machinist need for a dimension of 3/32 ± 1/64th inches for a go/no go gage setup (rounded to three places)?

a) 0.332/0.312
b) 0.110/0.094
c) 0.094/0.078
d) 0.110/0.078
SPC

• Definition of the range applied in SPC

• Chart used to measure variation between parts in a sampling


32) A measure of dispersion that uses the largest and smallest measurements of a sampling is the:

a) Range
b) Mean
c) Median
d) Mode
e) Radian

Rest is given in word file.
Attached Files Available for Download
File Type: doc NIMS question paper.doc (89.0 KB, 119 views)
__________________
Answered By StudyChaCha Member
Reply With Quote
Reply


Reply to this Question / Ask Another Question
Your Username: Click here to log in

Message:
Options



All times are GMT +6.5. The time now is 08:35 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions, Inc.
Search Engine Friendly URLs by vBSEO 3.6.0 PL2

1 2 3 4 5 6 7 8