2022-2023 StudyChaCha

#1
December 31st, 2013, 05:13 PM
 Super Moderator Join Date: Jun 2013
ONGC Exam Mechanical Engineering Question Paper

Would you like to provide here the ONGC Exam Mechanical Engineering Question Paper?

As you are looking for ONGC Exam Mechanical Engineering Question Paper , so on your demand I am providing same here :

ONGC Exam Mechanical Engineering Question Paper

ONGC Exam Mechanical Engineering syllabus
APPLIED MECHANICS AND DESIGN

Engineering Mechanics: Free body diagrams and equilibrium; trusses and frames; virtual work; kinematics and dynamics of particles and of rigid bodies in plane motion, including impulse and momentum (linear and angular) and energy formulations; impact.

Strength of Materials: Stress and strain, stress-strain relationship and elastic constants, Mohrs circle for plane stress and plane strain, thin cylinders; shear force and bending moment diagrams; bending and shear stresses; deflection of beams; torsion of circular shafts; Eulers theory of columns; strain energy methods; thermal stresses.

Theory of Machines: Displacement, velocity and acceleration analysis of plane mechanisms; dynamic analysis of slider-crank mechanism; gear trains; flywheels.

Vibrations: Free and forced vibration of single degree of freedom systems; effect of damping; vibration isolation; resonance, critical speeds of shafts.

Design: Design for static and dynamic loading; failure theories; fatigue strength and the S-N diagram; principles of the design of machine elements such as bolted, riveted and welded joints, shafts, spur gears, rolling and sliding contact bearings, brakes and clutches.

FLUID MECHANICS AND THERMAL SCIENCES

Fluid Mechanics: Fluid properties; fluid statics, manometry, buoyancy; control-volume analysis of mass, momentum and energy; fluid acceleration; differential equations of continuity and momentum; Bernoullis equation; viscous flow of incompressible fluids; boundary layer; elementary turbulent flow; flow through pipes, head losses in pipes, bends etc.

Heat-Transfer: Modes of heat transfer; one dimensional heat conduction, resistance concept, electrical analogy, unsteady heat conduction, fins; dimensionless parameters in free and forced convective heat transfer, various correlations for heat transfer in flow over flat plates and through pipes; thermal boundary layer; effect of turbulence; radiative heat transfer, black and grey surfaces, shape factors, network analysis; heat exchanger performance, LMTD and NTU methods.

Thermodynamics: Zeroth, First and Second laws of thermodynamics; thermodynamic system and processes; Carnot cycle. irreversibility and availability; behaviour of ideal and real gases, properties of pure substances, calculation of work and heat in ideal processes; analysis of thermodynamic cycles related to energy conversion.

Applications: Power Engineering: Steam Tables, Rankine, Brayton cycles with regeneration and reheat. I.C Engines: air-standard Otto, Diesel cycles. Refrigeration and air-conditioning: Vapour refrigeration cycle, heat pumps, gas refrigeration, Reverse Brayton cycle; moist air: psychrometric chart, basic psychrometric processes. Turbomachinery: Pelton-wheel, Francis and Kaplan turbines impulse and reaction principles, velocity diagrams.

MANUFACTURING AND INDUSTRIAL ENGINEERING

Engineering Materials: Structure and properties of engineering materials, heat treatment, stress-strain diagrams for engineering materials.

Metal Casting: Design of patterns, moulds and cores; solidification and cooling; riser and gating design, design considerations.

Forming: Plastic deformation and yield criteria; fundamentals of hot and cold working processes; load estimation for bulk (forging, rolling, extrusion, drawing) and sheet (shearing, deep drawing, bending) metal forming processes; principles of powder metallurgy.

Joining: Physics of welding, brazing and soldering; adhesive bonding; design considerations in welding.

Machining and Machine Tool Operations: Mechanics of machining, single and multi-point cutting tools, tool geometry and materials, tool life and wear; economics of machining; principles of non-traditional machining processes; principles of work holding, principles of design of jigs and fixtures

Metrology and Inspection: Limits, fits and tolerances; linear and angular measurements; comparators; gauge design; interferometry; form and finish measurement; alignment and testing methods; tolerance analysis in manufacturing and assembly.

Computer Integrated Manufacturing: Basic concepts of CAD/CAM and their integration tools.

Production Planning and Control: Forecasting models, aggregate production planning, scheduling, materials requirement planning.

Inventory Control: Deterministic and probabilistic models; safety stock inventory control systems.

Operations Research: Linear programming, simplex and duplex method, transportation, assignment, network flow models, simple queuing models, PERT and CPM.

The ONGC Exam Mechanical Engineering Questions are follows:

1 During the execution of a CNC part program block NO20 GO2 X45.0 Y25.0 R5.0 the type of tool motion will be
A) circular Interpolation — clockwise
B) circular Interpolation — counterclockwise
C) linear Interpolation
D) rapid feed

2 A component can be produced by any of the four processes I, II, III and IV. Process I has a fixed cost ofRs. 20 and variable cost of Rs. 3 per piece. Process II has a fixed cost Rs. 50 and variable cost of Re. 1 per piece. Process III has a fixed cost of Rs. 40 and variable cost of Rs. 2 per piece. Process IV has a fixed cost of Rs. 10 and variable cost of Rs. 4 per piece. If the company wishes to produce 100 pieces of the component, from economic point of view it should choose
A) Process I
B) Process II
C) Process III
D) Process IV

3 In an interchangeable assembly, shafts of size 25.000+0.040mm mate with holes of size 25.000+0.020 mm. The maximum possible clearance in the assembly will be
A) 10 microns
B) 20 microns
C) 30 microns
D) 60 microns

4 A company has two factories S1, S2 and two warehouses D1, D2. The supplies from S1 and S2 are 50 and 40 units respectively. Warehouse D1 requires a minimum of 20 units and a maximum of 40 units. Warehouse D2 requires a minimum of 20 units and, over and above, it can take as much as can be supplied. A balanced transportation problem is to be formulated for the above situation. The number of supply points, the number of demand points, and the total supply (or total demand) in the balanced transportation problem respectively are
A) 2, 4, 90
B) 2, 4, 110
C) 3, 4, 90
D) 3, 4, 110

5 An incompressible fluid (kinematic viscosity, 7.4 x 10-7 m2/s, specific gravity, 0.88) is held between two parallel plates. If the top plate is moved with a velocity of 0.5 m/s while the bottom one is held stationary, the fluid attains a linear velocity profile in the gap of 0.5 mm between these plates; the shear stress in Pascals on the surface of top plate is
A) 0.651 x 10-3
B) 0.651
C) 6.51
D) 0.651 x 103

6 The tool of an NC machine has to move along a circular arc from (5,5) to (10,10) while performing an operation. The centre of the arc is at (10,5). Which one of the following NC tool path commands performs the above mentioned operation?
A) N010 G02 X10 Y10 X5 Y5 R5
B) N010 G03 X10 Y10 X5 Y5 R5
C) N010 G01 X5 Y5 X10 Y10 R5
D) N010 G02 X5 Y5 X10 Y10 R5

7 During a Morse test on a 4 cylinder engine, the following measurements of brake power were taken at constant speed.
All cylinders firing 3037 kW
Number 1 cylinder not firing 2102 kW
Number 2 cylinder not firing 2102 kW
Number 3 cylinder not firing 2100 kW
Number 4 cylinder not firing 2098 kW
The mechanical efficiency of the engine is
A) 91.53%
B) 85.07%
C) 81.07%
D) 61.22%

8 In terms of theoretical stress concentration factor (Kt) and fatigue stress concentration factor (Kf ), the notch sensitivity ‘q’ is expressed as
A) (Kf -1) (Kt -1)
B) (Kf -1) (Kt +1)
C) (Kt -1) (Kf -1)
D) (Kf +1) (Kt +1)

9 Starting from x0 = 1, one step of Newton-Raphson method in solving the equation x3 + 3x -7 = 0 gives the next value (x1) as
A) x1 = 0.5
B) x1= 1.406
C) x1= 1.5
D) x1 = 2

For detailed paper here is attachment:
 ONGC Exam Mechanical Engineering Paper.doc (71.0 KB, 2038 views) ONGC Exam Mechanical Engineering Paper.pdf (30.6 KB, 22546 views) ONGC Exam Mechanical Engineering Question Paper.pdf (760.4 KB, 111 views)

Last edited by Aakashd; December 22nd, 2019 at 05:04 PM.

#2
April 9th, 2014, 02:28 PM
 Junior Member Join Date: Apr 2014
Re: ONGC Exam Mechanical Engineering Question Paper

Quote:
 Originally Posted by Unregistered Would you like to provide here the ONGC Exam Mechanical Engineering Question Paper?
Would you like to provide here the ONGC Exam Mechanical Engineering Question Paper?[/QUOTE]
#3
June 20th, 2014, 01:11 PM
 Junior Member Join Date: Jun 2014

Quote:
 Originally Posted by dnyanesh5588 Would you like to provide here the ONGC Exam Mechanical Engineering Question Paper?
[/QUOTE]

Plese, provide whole papers of mechanical Engineering for ongc graduate trainee
#4
October 24th, 2014, 11:41 PM
 Unregistered Guest
Re: ONGC Exam Mechanical Engineering Question Paper

Plese, provide whole papers of mechanical Engineering for ongc graduate trainee[/QUOTE]

rayudusai009@gmail.com please kindly sent me Q/A PAPERS
#5
November 21st, 2014, 05:47 PM
 Unregistered Guest
Re: ONGC Exam Mechanical Engineering Question Paper

Quote:
 Originally Posted by Unregistered Plese, provide whole papers of mechanical Engineering for ongc graduate trainee
rayudusai009@gmail.com please kindly sent me Q/A PAPERS[/QUOTE]
#6
January 28th, 2019, 02:29 PM
 Unregistered Guest
Re: ONGC Exam Mechanical Engineering Question Paper

Hi buddy I have applied for ONGC recruitment Exam and here I am searching for Mechanical Engineering subject question Paper , so would you plz provide me same here ??