IES Mechanical Papers Download - 2016-2017 StudyChaCha

Go Back   2016-2017 StudyChaCha > StudyChaCha Discussion Forum > Exams

Old April 5th, 2013, 06:14 PM
Amit Mila
Posts: n/a
Default IES Mechanical Papers Download

Sir, please provide me the IES Mechanical Papers.
Reply With Quote Quick reply to this message
Old April 6th, 2013, 07:10 PM
Super Moderator
Join Date: Dec 2011
Posts: 11,219
Default Re: IES Mechanical Papers Download

Here I am providing the Question paper of IES Mechanical 2008.

1. What is the additional time available for the performance of an activity in PERT and CPM calculated on the basis that all activities will start at their earliest start time, called?
a. Slack
b. Total float
c. Free float
d. independent float

2. In the basic EOQ model, if demand is 60 per month, ordering cost is Rs. 12 per order, holding cost is Rs. 10 per unit per month. What is the EOQ?
a. 12
b. 144
c. 24
d. 28

3. Which one of the following is correct? In tile basic EOQ model, if lead time increases from 5 to 10 days, the EOQ will
a. double
b. decrease by a factor of two
c. remain the same
d. The data is insufficient to find EOQ

4. Which one of the following statements is not correct
a. Work sampling is a technique of work measurement
b. Method study is a technique aimed at evolving improved methods.
c. Synthetic data is not a technique covered under pre-determined motion time systems
d. ‘Select’ is the first step of method study

5. A time standard for a data entry clerk is to be set A job is rated at l20 percent, it takes 30 seconds to enter each record and the allowances are 15%. What is the normal time?
a. 25 seconds
b. 30 seconds
c. 36 seconds
d. 40 seconds

6. Consider the following statements:
1. The amount of interference needed to create a tight joint varies with diameter of the shaft.
2. An interference fit creates no stress state in the shaft.
3. The stress state in the hub is similar to a thick-walled cylinder with internal pressure.
Which of the statements given above are correct?
a. 1, 2 and 3
b. 1 and 2 only
c. 2 and 3 only
d. 1 and 3 only

7 . Consider the following statements:
A nomenclature 50 H8/p8 denotes that
1. hole diameter is 50 mm.
2. it is a shaft base system.
3. 8 indicates fundamental deviation.
Which of the statements given above is/are correct?
a. 1, 2 and 3
b. 1 and 2 only
c. I and 3 only
d. 3 only

8. Consider the following:
V-belts are specified by their
1. nominal inside length in mm
2. nominal pitch length
3. belt cross section symbol
4. weight/unit length of the belt
Which of the above are correct?
a. 1, 2, 3 and 4
b. 1 and 2 only
c. 1 and 3 only
d. 3 and 4 only

9. Consider the following statements:
Maximum shear stress induced in a power transmitting shaft is
1. directly proportional to torque being transmitted.
2. inversely proportional to the cube of its diameter.
3. directly proportional to its polar moment of inertia.
Which of the statements given above are correct?
a. 1, 2 and 3
b. 1 and 3 only
c. 2 and 3 only
d. 1 and 2 only
Attached Files
File Type: pdf IES Mechanical Papers 1 2008 .pdf (131.0 KB, 57 views)
File Type: pdf IES Mechanical Papers 2 2008.pdf (130.7 KB, 55 views)
Answered By StudyChaCha Member
Reply With Quote Quick reply to this message
Sponsored Links

Other Discussions related to this topic
ITI Diesel Mechanical Question Papers
Old papers of NTPC Recruitment of Mechanical
Phd Entrance Question Papers Mechanical
EIL papers for Mechanical
Old Question papers of I.E.S mechanical
ONGC Mechanical Question Papers
MU Sigma Placement Papers For Mechanical
Old question papers for STA B Mechanical Engineering
IES Mechanical Papers Free
ISRO Mechanical Solved Papers
Chargeman II(Mechanical) Sample papers
NDA Papers Download
ABB Question Papers For Mechanical Engineers
HAL placement papers mechanical engineering
IES Mechanical Papers Pdf
EIL Previous Year Papers Mechanical
CET Papers Download
IES Sample Papers Mechanical
HAL Placement Papers Mechanical
IES Mechanical Papers Solved

Have a Facebook Account? Ask your Question Here


Reply to this Question / Ask Another Question
Your Name: Click here to log in


Forum Jump

All times are GMT +6.5. The time now is 05:40 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Friendly URLs by vBSEO 3.6.0 PL2

1 2 3 4 5 6 7 8 9