BHEL Supervisor Trainee mechanical engineering paper - 2017-2018 StudyChaCha

Go Back   2017-2018 StudyChaCha > StudyChaCha Discussion Forum > General Topics




  #1  
Old December 31st, 2013, 05:47 PM
Unregistered
Guest
 
Posts: n/a
Default BHEL Supervisor Trainee mechanical engineering paper

Here I am looking for the BHEL Supervisor Trainee mechanical engineering paper, kindly provide me the same……
Reply With Quote
  #2  
Old January 2nd, 2014, 11:47 AM
Super Moderator
 
Join Date: Jun 2013
Posts: 42,987
Default Re: BHEL Supervisor Trainee mechanical engineering paper

As you are looking for the BHEL Supervisor Trainee mechanical engineering paper, here I am uploading a pdf file that contains the same. You can use this question paper in your studies. I have taken following questions from the attachment:

17)Why DC current is not used in transformer.

18)On what principle the sonar/ radar works?

19)Bending moment diagram for the UDL is in what shape?

20)Function of the distributor in petrol vehicles? (Spark timing) 21)Which is not present in CI engines?
(carburrettor)

22)What will happen if one cylinder recieves more amount of fuel spray from injectors than other
injectors?

23)Purpose of draft tube in hydraulic turbines? (The purpose of a draft tube is toconvert some of the
kinetic energy of the flow from the runner (the rotating part of the turbine) intopressure energy and
thereby increase the efficiency ofthe hydro power turbine.)

24)What is the effect or reheater in the gas turbine? (The advantage of reheater is significantly
increased thrust; the disadvantage is it has very high fuel consumption and inefficiency) )Problems
involving with fricition coefficient.

26)Factor of safety = Yeild stress/Working stress. 27)Which is the example of non parallel power
transmission (Universal coupling) 28)For perpendicular shafts worm gear is used.

Remaining questions are in the attachment, please click on it…..
__________________
Answered By StudyChaCha Member
Reply With Quote
Sponsored Links






















  #3  
Old February 21st, 2015, 06:48 PM
Super Moderator
 
Join Date: Dec 2011
Posts: 11,219
Default Re: BHEL Supervisor Trainee mechanical engineering paper

As per your need, I am giving you question paper of the BHEL Supervisor Trainee mechanical engineering Paper.

Unit of Entropy (J/kg K or kJ/kg K)

A mass of 100kg is falling from a height of 1 m and penetrates the sand into for 1 m. What is the resistance force given by sand.

Ratio of specific heats of air. (1.41)

A body weighs 3 kg in air. If it is submerged in a liquid, it weighs 2.5 kg. What is the specific gravity of the liquid.

Two cars travell in same direction at 40 km/hr at a regular distance. A car comes in a opposite direction in 60km/hr. It meets each car in a gap of 8 seconds. What is the distance between them?

A simple problem involing in hoops stress. For sphere: M= [3/2]*p*V*[density of pressure vessel material/Maximum working stress it can tolerate] For Thin walled pressure walls: Hoops stress or stress in the radial direction =p*r/2t

A problem in force calculation in a body moving in a inclined surface.

Composition of bronze. (Copper+zinc)

Compostion of stainless steel.(iron+chromium+nickel+carbon)

CI is manifactured in which process. (cupola process) 11)What percentage of carbon is preset in pig iron. (4.5 to 6%)

Water is available at 10m height. What is the pressure available? (pressure=density*g*height; p=1000*9.81*10; p=98100N/m2) Ch

What will happen if the speed of the centrifugal pump doubles.

The unit eV is widely used in ? (Nuclear and atomic physics)

What will happen to the resistance, when the diameter of the conductor is doubled?

The power comsumed by a electrical device is 1000W at 250V, What is the resistance in the device? (Power= Voltage*current; Current=Power/Voltage, Current,I=1000/250=4 amps. V=IR, Therefore R=250/4=62.5 ohms)

A planet gear with 25 teeth is meshed with a sun gear of 100 teeth. Both are connected using a arm. How many rotations are needed for planet gear to complete one rotation around the sun gear?

What is equivalent spring constant for spring in parallel?

Some questions was asked related to boundry layer and vortex flow.

5 questions were asked in PERT, Process planning, Product planning, Break even analysis.

How are tungsten and sintered composite materials are machined? (Electro Discharge Machining, EDM)
__________________
Answered By StudyChaCha Member
Reply With Quote
Other Discussions related to this topic
Thread
BHEL Supervisor Trainee (Mechanical) previous year question papers
BHEL Supervisor Trainee Exam Pattern
BHEL Supervisor Trainee Exam Syllabus
Permition Slip for Supervisor Trainee in BHEL
Preparation for BHEL supervisor trainee exam (Mechanical)
BHEL Supervisor Trainee Question Paper
BHEL Mechanical Supervisor Trainee previous year question papers
BHEL Supervisor trainee (ME) old paper and pattern
Paper for BHEL Supervisor Trainee Electronics & Communication
BHEL Supervisor Trainee Exam Date
BHEL supervisor trainee exam syllabus
BHEL Supervisor Trainee Electrical Previous Paper
BHEL Supervisor Trainee Mechanical old papers
Question Paper for BHEL Supervisor Trainee
BHEL Supervisor Trainee Exam Preparation
Syllabus for BHEL examination for supervisor trainee cadre
Syllabus for BHEL Supervisor Trainee (Mechanical Engg)
BHEL Supervisor Trainee Question Papers
BHEL Supervisor trainee (ME) syllabus
Technical test for supervisor trainee for BHEL






Have a Facebook Account? Ask your Question Here



Reply


Forum Jump


All times are GMT +6.5. The time now is 05:18 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Friendly URLs by vBSEO 3.6.0 PL2

1 2 3 4 5 6 7 8 9