APTransco model questions - 2018-2019 StudyChaCha

#1
August 4th, 2012, 12:59 PM
APTRANSCO Model Questions

I am taking part in the Andhra Pradesh Transmission Corporation Limited exam so I need the Model Question papers of the APTRANSCO so give me the papers and tell me from where I can download the papers?
#2
June 6th, 2013, 01:23 PM
 Unregistered Guest Posts: n/a
APTransco model questions

Will you provide me APTransco model questions of Electrical Sub Engineer?

#3
June 6th, 2013, 02:39 PM
 Senior Member Join Date: May 2013 Posts: 16,364
Re: APTransco model questions

I am giving some Question Papers of APTRANSCO Electrical Sub Engineer:

1. The Resistance of Armature Winding depends up on
a) Number of conductors
b) Length of conductor
c) Cross sectional area of the conductor
d) all of the above

2. The pole pitch of the four pole dc generator provided with a two layer lap winding with sixteen coils is
a) 4
b) 16
c) 32
d) 8

3. The thickness of lamination of dc machines is
a) 0.005 mm
b) 0.05mm
c) 0.5mm
d) 5mm

4. The purpose of providing dummy coils in the generator is
a) To reduce eddy current losses
b) To enhance flux density
c) To amplify voltage
d) To provide mechanical balance for the rotor

5. The material used for commutator brushes is
a) Copper
b) Mica
c) Carbon
d) Cast iron

6. For generating large currents on DC generators, which winding is generally preffered
a) Lap winding
b) Progressive winding
c) Retrogressive winding
d) Current depends on design

7. The direction of rotation of dc series motor can be changed by
a) Interchanging the supply coils
b) Interchanging field terminals
c) a or b
d) None

8. DC motor connected across AC supply results in
a) Motor will burn
b) Motor will run at rated speed
c) Motor will run at corresponding synchronous speed
d) Motor will run at slow speed

9. In Flemings left hand rule if the forefinger points in the direction of the field or flux, then the middle finger will point in the direction of
a) Current in the conductor
b) Movement of conductor
c) Resultant force on conductor
d) None

10. The synchronous speed of a motor with 6 poles and operating at 50 Hz frequency is
a) 1500 b) 1000
c) 3000 d) 750

11) Which types of following motors are most efficient?
a) TEFC b) SPDP
c) Both d) None

b) Temperature of the winding
c) Age of the motor
d) Ambient conditions

13) Unbalance in voltages at motor terminals is caused by ____.
a) Supplying single phase loads disproportionately
b) Use of different sizes of cables
c) Both (a) & (b)
d) None

14) Application of DC motors is generally restricted to a few load speed applications because of _____.
a) Cost of the motor is high b) problems with mechanical commutation c) Maintenance problems d) None of the above

15) Which of the following information available on name plate of a motor?
a) HP rating b) RPM c) Frame model d) all the above

16) The form factor for sinusoidal waveform is
1) 1.00 2) 1.11 3) 1.732 4) 2.2

17) The rotor resistance and reactance of a three-phase induction motor is 0.2 ohm and 2 ohm respectively. The per unit slip corresponding to maximum torque is equal to
1) 9.02 2) 0.01 3) 0.1 4) 0.2

18) Load factor is defined as the ratio of
1) Average power demand to maximum power demand
2) Minimum power demand to maximum power demand
3) Maximum power demand to minimum power demand
4) Average power demand to minimum power demand

19) The unit of luminous flux is
1) Lux 2) candle Power 3) Metre Cancle
4) Lumen

20) For 132 KV transmission line, the insulators commonly used are
1) Strain type 2) Pint type 3) Suspension type
4) Shackle type

21) DC Transmission lines are free from
a) Inductance
b) Capacitance
c) Phase Displacement
d) All

22) DC Transmission lines are free from
a) Skin Effect
b) Corona Effect
c) Resistance Drop
d) All

23) Transmission efficiency increases as
(A) Voltage and power factor both increase
(B) Voltage and power factor both decrease
(C) Voltage increases but power factor decreases
(D) Voltage decreases but power factor increases

24) In overhead transmission lines the effect of capacitance can be neglected when the length of line is less than
(A) 200 km
(B) 160 km
(C) 100 km
(D) 80 km

25) The disadvantage of constant voltage transmission is
(A) Short circuit current of the system is increased
(C) Large conductor area is required for same power transmission
(D) Air of the above

26) The current drawn by the line due to corona losses is
(A) Sinusoidal
(B) Square
(C) Non-Sinusoidal
(D) Triangular

27) Which distribution system is more reliable ?
(A) Ring main system
(B) Tree system
(D) All are equally reliable.
28) Step-up substations are associated with
(A) Distributors
(B) Consumer location
(D) Generating stations

29) A bus bar is rated by
(A) Current only
(B) Current and voltage only
(C) Current, voltage, frequency
(D) Current, voltage, frequency and short time current

30) Ina transformer the energy is conveyed from primary to secondary through
a) Air
b) Cooling oil
c) Flux
d) None

31) The basic electrical Quantities are
a) Charge and voltage
b) Energy and current
c) Charge and energy
d) Voltage and current

32) For a DC voltage an inductor acts as
a) Open circuit
b) Short circuit
c) Finite resistance
d) A voltage source

Quote:
 Originally Posted by Unregistered Will you provide me APTransco model questions of Electrical Sub Engineer?